Z'ednannya darts crimped from plastic. How to pick up the richly-living darts at the well. Bonded with the zapobіzhniks

A rich supply of blame for the hour of work with electricity, as if it were not less than equally safe, but also in the way of loading the elements. Find out from the information of the masters, sometimes they blame the supers, which method is better to choose in a specific situation. Dosit often vikoristovuyut clemy for z'єdnanny drotіv. Let's take a look at their peculiarities and the riven of superstition.

Diversity of types of terminals

Throw back the darts carefully and respectfully, if the technology is damaged, it can be short chirp otherwise, just don’t fit in after the repair. At the municipality, contacts are subject to the following standards:

• Nadіynіst without additional support. Tobto it is not guilty to revisit the wild opir of the whole dart.
• The material is mechanical, which shows the stretch marks. The place of the zchipka is not guilty of ruining for any manipulations with the wire.

You can see some ways of fixing a broken cable, which will be looked at in more detail below.

Wicked structure

The simplest and most extensive way. It is necessary to take two darts and take out an insulating ball (more than 50 mm), and then twist them naked.

After the nadіyny z'єєdnannya lived, I should renew the opening of the litter, for which I would call to put the PLV line. And you can also zastosuvat "cow for twisting."

Get respect! It is not possible to return various darts in such a way.

Related article:

At the article, we can clearly see the design, the average variety and the material, from which it is prepared corrugated pipe, as well as how to properly practice with the cim attachment.

soldering

The process itself takes three hours more than an hour, the lower structure, and then the robot comes out again. If there is no supplementary support, which is all the same when twisted. The spike is also unbearable for a short flicker, as it can be blamed for an incorrect structure.

Korisna's joy! Tin-lead solder and rosin are used for soldering.

Zastosuvannya adhesive pads

Adhesive block - a circuit board with contacts. This is a kind of connector for connecting wires, moreover, it should be installed for various options, for example, copper and aluminum.

Adhesive pads different for the method of fastening:

• with screw for tightening;
• with tight dresses.

The first option may be short - the possibility of a poor life lived with a twist, which is especially negligible when wires are connected with a large number of veins. Another variant is superior, for the fact that the maid is necessary to simply press on with a scarf.

Spring terminal for wire connection

Samy Swedish method skriplennya. For a new requirement, remove the ball of insulation from the wire struma and insert it into the terminal. In case of fixation, it is necessary to use an additional pressure clamp.

Firms, yakі vypuskayut danny pristroї for zchіpki rich. And for their help, you can close it like a soft one with a great number of lived, so with one living, moreover, with a different cut. For the help of such terminals, it is possible to install aluminum honey darts among themselves, the shards of shawls zastosovuyutsya, like pokryvayutsya especially sumishsh, scho appearing oxide.

Related article:

Looking around, we can look at the methods of vimir: the strength of the struma, the support. How to overturn capacitors field transistors, as well as to carry out diagnostics of ear infections.

Clamps for connecting wires: differences and features

Be it an installer and an electrician, he knows all the main types of gluers. In general, they can be divided into twins and without twins. The first variant is less nadіyny, for those who through the gwent can get naked lived.

All options are placed in a plastic or kapron case (maybe cabol) as well as secure insulation and keep a contact group at the warehouse (mechanism for connecting wires).

Get respect! Often for zastosuvannya klіnets kіnets zchіpki zchіpka

Endings are not needed for wires made of stranded conductors, which are squeezed without a victorious tip. At the same time, at the transitions, it is necessary to ensure the least amount of heat that is available for the calculation of the number of factors:

• finding the optimal bet for metals;
• zastosuvanya quartz-green oil anti-oxidation;
• design features The clamps transfer the tightening rod of the tip to the contact group.

The choice of the required bet transfers the choice of metal, from which a group of contacts is prepared. Conducted and tips are made from midi, aluminum or luden midi. Good contact with such types of material is ensured by steel, brass and special alloys, which form groups of contacts.

How to connect aluminum wire with a medium wire is simple: photo and video

It is not possible to allow direct twisting of midi and aluminum, since such a contact is not durable and can lead to a zamikannya, to overcome the problem, vicorist clamps for darts.

There is a way, if you can manage without a special connector, for which you will need a screw or a nut. Such a way allows you to put together practically whether there are a few elements, which are less than the length of a screw. Z'ednannya can be wired with wires of different comradeship and different metal, as well as single-core and multi-core options.

Sequence diy	photo stock
On the back of the hand, take the gwent of the necessary dozhina.
Know the conductors of the insulation ball, which is better than the diameter of the opposite feint. Moreover, the oxidation lived unnecessarily clean up to shine.
Form a ring.
Now, sequentially, put a spring washer, a special washer, a ring, a washer, another ring, a washer on the gvint. Finish with a nut, twisting the screw, docks straighten the spring washer.

So in a simple way you can throw a sprat of darts into the air. As if you are planning to win a rich variant, try it with solder. To make it easier to understand, take a look at the video material, for example, statistics.

If a terminal block has sagged under your hand, everything will be much simpler. In case of any otrimane, the seal does not require additional insulation as an option with a bolt. In order to vikonate, I gave a zchіpka, enough to clean it from the ball of insulation to a length of 0.05 cm and insert it into the opening, twisting the zipper.

Krim zadnannya darts for additional zatiskachiv at the terminal blocks, you can vikoristovuvat Іnshiy variant of attachment, devikoristovuєtsya spring principle. Є variant of the bagatoraza vikoristannya connector, which is more convenient.

Conductors for dart clamps

Navit so pristosuvannya, as a terminal should be carefully selected, even in the case of її nadіynostі and durability stale stability of the work cable. Koristuvachs have made a rating of light types of such connectors, as well as models of such connectors.

Up to the TOP-3 wired terminals for the wire connection have gone:

• Samtec takes the first position (USA).
• In another place, there is also a picker from the USA - Kycon
• HARTING Nіmechchina - the third place in the rating.

The Samtec company offers a professional tool for trimming wire terminals - a CAT-HT-281-2430-13 ratchet for the middle grade of 30,010. Kycon GAX-4-88 for the middle grade of 600 rubles. a piece.

Or you can choose cheap and simple options, for a price of 200 UAH. a piece. In any case, pick up conectors who come out of the number of veins, which will come together, and elements.

Video: production of copper and aluminum rods

At the end

The selection of various modifications of the terminals significantly simplifies the wiring, and the material is prepared differently. You can twist and twist the method of twisting or soldering, which will not be on the flooring.

Z'ednuyuchi midny that aluminum wire but, don’t forget that you can’t work directly, just twist the bolt or the connector.

Selecting a connector, marveling at the number of roses, the brand-maker and other characteristics I will add. If you want to choose independently, you can turn to professionals after consultation.

If you want to do it, you don’t need anything better for the wires, clean them with a knife, twist and wrap them with electrical tape, wind up in life. Today, there are already a lot of alternative outbuildings, which will make the process of wire installation much easier, and at the same time, get the necessary ones. Hours will soon pass away at the liota, for different cleats will come to replace them.

Why are glues good? How, for example, would the date be superb and long-term?

Curbievati M_D z aluminінm is categorically possible, Alege Todi is confused by Galvanіchna Couple, I Corzіya is just Zrunuє Z'єєєднаннна, with Cyomo, it's not an increase in the magnitude of the magnitudes of the jets in a twist, it's too early to schi pіsno, and Yakscho Struse Budshe, inclusive - Vimknennya , then the opir twisting increases more and more quickly, with the heating of the place the twisting becomes more and more.

Zreshtoy, tse can call until later, or in a shorter fall - the smell of melted insulation. Klemy in this situation vryatuly b, and until the collapse of the month the contact on the right did not b.

The most simple solution is to put it. Polyethylene terminal blocks are sold today in the leather electrical goods store and are not expensive. The middle of the polyethylene frame is stitched into a row of tubules (sleeves) made of brass, in some wires, which are connected, and are squeezed with two screws. For the bazhannya, you can buy skils for the use of polyethylene tubes, and for the cost of skils for the need for pairs of darts.

However, not everything is so radiant, aluminum flow under the pressure of gwent at room temperature, it will be periodically, quickly, necessary to lift the load. Otherwise, there is a lot of trouble on the right middle conductors, everything will be all right.

If you don’t pull the aluminum wire at the same time, which hits the terminal, then throw a dart, if you have used too much contact, you will spark and heat up, but I’ll threaten it later. It is impossible to squeeze into such a terminal block rich-core darts without additional pin tips, we’ll talk about them later.

If you just squeeze the bagatozhilny drіt near such a terminal, then the vice of the screw lived on thin, near the wrappings and the uneven surface, leading to the fact that part of the lived came to inapplicability, but I would threaten it with overheating. Well, if a rich veil should be carried out according to the diameter of the sleeve - the most acceptable variant of the closure, even if the risk of damage to the closure is less.

As a result, it is possible to produce visnovoks, which polythene terminals are good for single-core, and only for medium darts. It’s necessary to squeeze in a bagatozhilny, to put on an additional tip, about which it will be said later.

The next option is handy Happy Clem- . Such terminal pads are equipped with more transparent caps, which can be taken for bazhannya. The fastening is even simpler: after cleaning, the dart is thrust between the pressure and contact plates, and squeezes behind the help of the screw.

Why are such terminals superior? First, on the view of polyethylene terminals, plastic terminals, there is an even steel pressure, there is no direct pressure of the screw on the living. Pressed part of the maє viїmku pіd provіd. At the result, the terminals will be blocked for the connection of the group. Why groupie? The one who cuts this terminal block, like polyethylene, does not go into it.

Dali - self-tightening clamps, with the butt of which you can buti. Ce express-clemi for quick one-time wiring installation. It is carried out until the end of the middle of the opening, and there it automatically fixes the pressure plate, which is pressed down to a special ludno tavern. Pressing susilla is saved for the whole hour of the pressure on the material of the pressure plate.

Express clamps are disposable, but in principle they can be carried out, quietly wrapping yoga in the process of winding. Ale, if you pull the wire, then the devil’s work is better than working in a new grip, fortunately, the stench is not expensive, 10-20 times cheaper for the terminal blocks.

The inner plate of the middle plate is light, and allows you to fix any aluminum, even the middle darts. Prettyskne zusillya is taken care of without interruption, and it will not be possible to pick it up carefully, as it is with terminal blocks.

Use the same oil on the basis of quartz sand with technical vaseline, for abrasive, which uses oxide smelting, to apply on the surface of the drota, which will protect, vaseline, and reappear. Dani ekspres-klemi buvayut transparent and opaque. At the same time, plastic does not support the mountain.

Suitable for z'ednan іz perebachuvany strum up to 25A. Clamps of other types can suffer from heating, for example, weaker pressure of spring contacts, so use only firm clamps, which you have recommended yourself well.

How bagatorazovyh clamps go. All terminals with important zatiskachami. Here you can also squeeze darts of different types. The process of strengthening is simple: the importance is lifted, the dart is put in, what is squeezed, the importance is pressed - fixation is made.

Zatyskach tsey - bagatorazy. When you add important fixation, you can pull one wire and insert another one. This type of terminal is ideal for bagatorase reconfiguration of groups of conductors. Vitrimuє without overheating strum up to 32 amperes. The design of the troch's closure is similar to a one-time express closure, but I am aware of the fact that it is still possible to switch between the carriers, who are catching up.

Let's take a look. These are disposable muffs for darts, rozrahovany on a small jet. For additional scotch locks, you can put in telephone darts, low-power light fixtures, and so on.

Dekіlka wires, right in the insulation, inserted into the sleeve, then carried out by pressing for additional pasatizhiv. Structured cabling installers love scotch locks. Scotch locks allow you to put darts in without the need to clean them up. A plate with red contacts is easy to fit into the insulation, and come into contact with a conductor, with a residential one.

Scotch locks are on two and three lived. The peculiarity of such clamps is that they are cheap, waterproof, universal, and do not require stripping of ends, but are squeezed with simple pliers. The middle muffs are hydrophobic gel for contact protection against water and corrosion.

If you need to replace the z'ednannya, the scotch-lock is simply removed at once from the pieces of darts, and a new one is installed.

If it is necessary to connect a sprat of wires into one tight vuzol, for example, just combine them, or for laying on a terminal block, zastosovuyut sleeves. Sleeves of vicorist are most universal, tse sound luzhenі mid-sleeves in the form of tubes, or in the form of flat tips with a fastened latch.

Spend inserted into the sleeve, and crimped with a special tool - a crimper. Crimper- Tse. The greatness of the sleeves is for the fact that such a crimp does not create an elevated support on the mission of the day. The sleeves are in the form of a flat tip with a lapel, if it is necessary to fasten a wire or a bundle of wires on the body for an additional screw. Just pick up a sleeve with a wide diameter, vibrate the crimp, and attach the tip to where you need it.

For z'ednannya rich-core darts To connect single-core wires with rich wires, or just to fix them at the terminal blocks.

The hardwire is manually inserted into the tip, the tip is pressed together with the wire, so that the hardwire can be fixed in any kind of terminal block, connected to the polyethylene one, do not be afraid that the wire will collapse.

Virishal here appears correct choice the diameter of the tip, the vine is guilty of confirming the hard diameter of the pressed, bundled, alive, so that the darts do not jump out.

To trim the pins, you can use pliers or twist with a hammer.

Middle of the day of the obladnannya pіd hour installation electric lines in living quarters and industrial booths there are special attachments for wiring contacts. Terminal blocks for wire connections gradually gained popularity. How did you win them home wiring then it is necessary to know, how to be proud of them, how to prove different advantages in front of other methods of work.

It is necessary for us to give a commission to such an outbuilding. A terminal block is called a special electrical attachment, which looks like a block or a screw zatyskach. Yogo vikoristovuyut for schіlnogo z'єdnannya kontaktіv veins of different recognition. The Danish method is considered to be safe and effective for the introduction of aluminum and copper conductors. Thus, the cable is fixed in order to prevent the cable itself from being subjected to mechanical intrusions.

Rіznovidi

Іsnuє impersonal rіznоvidіv klemnikіv. Screw clamp. The most popular construction of screw fastening is the most popular design today. Vaughn at once and is simple, and nadіyna. The selection of twine terminals is often stagnated for breeding electrical wiring, for sockets and other plugs. Pratsiyuyut for the principle of a squeeze.

This type can be used for negative and positive terminals of the battery (and in car batteries), for the installation of a group of lighting elements and other extensions. Clemi in car batteries can be crushed with lead. Why is it due to the fact that the battery should replace acid for electricity. Most screw terminals are made from polycarbonate and resistant polypropylene. Ale їх also can work with polyamide or pressed polyethylene. The material can be found in the type of terminal block and in the same type.

Gvintove connection is not suitable for making aluminum contacts, because the stench is even more likely, and it can be harmful to make contacts. The stench is recognized for work with midwires. It is not uncommon for such a terminal block to be broken, with the necessary connection to a new ground wire. For tsyogo on nyomu, you can know a gvintik of green color. At qiu, the next point is grounded. Also, the new one has small teeth, yakі to improve the zcheplennya.

Obtisk clamp. This type of construction is used for connecting power cables, the width of which does not exceed 2.5 mm, and the power of the stream is 24 amperes. Obtiskny terminal building vitrimati navantazhennya up to 5000 volts. If you work harder, then you will need another way. The obtisk design allows you to connect up to 8 wires at the same time. For skin їх є okreme nest. Tse allows you to increase the security of the installation of electrical wiring. The zatiskachi can be automatic, as soon as they zatiskat insertions at the contact socket, the mechanical one, which needs to work independently. Just do not exceed the admissible bias on the terminal block, it may be garniy rіven naіynostі.

Insulating (ЗІЗ). Tsey type The best elements can look like a great plastic cap. It is prepared from a heat-resistant material - a polymer, which is not strong before borrowing. It is important that the wines serve for the protection of the wiring from the fire, the prote ZІZ building security and good mechanical contact of the cores. Wire contacts are twisted on special twisting. When this is done, the spring is pressed, as if it will improve the z'ednannya. If the twist itself is covered with a special paste, the metal can be oxidized. For the help of such a design, it is easy to fit no less than darts with a uniform retina, ale and medny with aluminum contact.

Okremo next designate a group of power terminals. The stench is more bulky and foldable design. Tse pov'yazano z tim, scho to them you can lead power cables with a different tovshchina pererazu, a different sweating, as well as a single midday lived with aluminium. The stinks of vikoristovuyutsya, if there is not about thin darts, but cables, the span of which can reach 300 mm 2. Fasten to the mounting plate or DIN rails. The contact plate is made from midi and covered with a tin alloy. With the help of washers of the final form, the bottom is not relaxed.

Universal and bar'ern terminal blocks. Other types are considered, that their designs have small metal smugs. The stench is separated by a ball of insulation. With the help of yoga, you can again turn off the dotik of the court wires. They are prepared with a high quality, making additional gvinti for the best reinforcement. You can make aluminium. Aluminium-contacts in such terminals are oxidized richer.

Carbolite terminal blocks can also be used with two types of cut. The stench of vikonanі from a specific alloy itself for these purposes. An indispensable material is ceramics, for which a suitable construction can be prepared, including a block.

Video "Types of terminals for connecting wires"

Yak koristuvatisya

It is important to know how to connect them to the new one for the help of terminals for the launch of power darts. Even more often zastosovuetsya fastening under the head of a twisted screw. Through the plates, the stripping contact of the cord is stretched, and then the fastening itself is tightened. Poshkodity element is possible with a constant scrolling of the gwent, but the very same will be even more necessary.

Passing combs and pads have special metal tips where the cord is to be wound. Let's have another day to come to the electric cabinet or another possession. The stocks also have screw locks. The pads are cheaper to buy and available in any specialized store. When zastosuvanni terminals in Wago enough to tighten the tightness, to start or pull the cable. Such a method of connection is suitable for fixing Wago only if it is bagatorasia.
With the exception of a one-time attachment to Wago, the reinforcement must be passed at a time, so that you can’t go back. For this yogo, you will have to take for help a nipper and a sharp knife.

In order to open the Wago terminal block, it is necessary to strip the wire in the outside insulation by approximately 1 centimeter. Then we need to raise the importance and start yoga in the middle, and then lower the clasp. The spring mechanism allows you to securely fix the conductor with a span up to 4 mm2.

Who has the advantage

Even often in electrical installation robots a private living house, or in the apartment of the master of the vicorist, wired using the method of extreme twisting, and rarely put soldering for fixing. Such a method of closing step by step is repaired by the construction of special structures - pads and terminals. The stench is not expensive and the varieties are available. The arrogance significantly shifts self-supporting, and also, with the help of them, you can easily and quickly turn on the connection to the structure, replacing the cord. For some examples of the pads or the wake-up call of Wago, this robot builds a new building. For the help of a smart and sensible design, you won’t take a lot of time in a difficult warehouse.

Virobnik Wago having made the attachment on such details even more we will forgive - a soft important, which secures the supply of aluminum and copper cables.
Zastosuvannya terminals in Wago allow you to arrive carefully, without contacts, what to wash, and protect the space in a pink shield. Wago charge is small, so that you can effectively connect both single-core and multi-core cables.

When wiring electrical wiring in an apartment or a house, it is necessary to vindicate a large number of people from the city and the house. For commutation of wires, a separate box is installed, and for a superficial connection of the jet conductors, a terminal block is used. Such electrical installation is not available see different and form a release that allows you to choose the best option for a particular release.

See different boxes

Behind the installation method, the box has two types:

1. Zovnishnya box zastosovuetsya at once from vіdkritim method of installation of electrical wires. Installed on surface walls;
2. For the installation of a attached rose box in the wall, there are burials, and attachments are installed in the yak. Zastosovuetsya zі attached electrical wiring: this method is the most popular

Rozpod_lna box may be white or black standard color. It is fallow in the air, you can add a decorative cover of the song color, which is suitable for the interior.

Material prepared

Fallow in recognition, separate boxes with different materials are issued. The most zastosuvannya was taken away by virobi, the body of some vikonanies made of metal and heat-resistant plastic.

• The metal case is made from luden steel or aluminum alloys by the casting method. Such conduits are victorious in industry for the connection of tight cables. For special minds of exploitation, the lid of the box and the good cuffs are equipped with strengthening gaskets. Tse allow vykonati z'єdnannya provіv for ekspluatatsії pіd vіd vіd vіd vіdіvіvnі vibuhonotbezpechnih gazіv;
• A plastic box with a base made of molded fluoroplast, more modern models of vikonan from refractory polypropylene. So it is not possible to burn, but melt under a surge of high temperatures. The very same see rozpodіlnyh boxes zastosovuyutsya for the installation of electrical wiring in living quarters.

Priestry

Use two types of attachment boxes:

1. In the case of pipes without terminals in the middle, for the connection of wires, twisting is carried out with a further insulation, or for additional caps;
2. Deyakі models are supplied with terminal blocks, yakі allow you to quickly and reliably connect and compress darts with different diameters. Another advantage of such electrical installations is the possibility of joining copper with aluminum, which is fenced for additional twisting work.

Get respect! Depending on the number of planned connections, you can choose the size of the box. Of cream, square, rectangular and round forms are produced.

Installation specifics

At attached to the installation electrical wiring, all elements are laid at a special burial place - strobes. To install a rozpodіlnoї box zagblennya to fight with a perforator or a special nozzle with a crown. Up to the wall, it is hard to crack for the help of a gypsum plaster or a dowel. AT frame booths special landing places are prepared for the installation of boxes.

The depth of the opening is opened in such a way that the body of the box protrudes 2-3 mm beyond the trim. It is necessary for the manual fixation of the lid.

After that, zgіdno z folded earlier by the connection scheme, the wires are connected. An important nuanceє nebhіdnіst zavodnіst kіnets drota in the body of the box with a small margin (approximately 10 cm).

See the terminal blocks

Since, as such, the characteristics of the rozpodіlnyh boxes, we look, as the main ones see good pads to be installed for home electrical wiring.

The same kind of quality and reliability safe operation electrical wiring. Therefore, the most important type of connection is the screw contact for the help of terminal blocks: they allow you to squeeze the vein in a good way. Terminals are suitable for single- and multi-core conductors, they also allow the connection of wires with a residential one, which may be smaller.

Depending on the type of plant and the minds of exploitation, choose one of the types of terminal blocks that are currently in use.

Polyethylene pads

Such varieties are made from white or transparent polyethylene, resistant to chemical manufacturers and other aggressive components. The plank is folded with a number of pairs of twin screws, which, if necessary, can be cut with a knife. Varto designate how small the inner diameter and mechanical strength are. Most often they are victorious for lighting, as well as connecting low-pressure light fixtures, for example, chandeliers.

Polyamide terminal blocks

Tsey type of pads can be more beautiful, lower front view operational characteristics. They are made from black polyamide, which does not lift the mountain. In the process of operation, polyamide can be heated up to 120 °C, without changing the shape (melting). Resistant to the age of retailers. Such successful outbuildings have known a wide zastosuvannya in pobuty, so they are more efficient and practical, suitable for a quick connection, no matter how quick to the electrical wiring.

Virobi with spring contacts

It is also safe to secure the outer contact of the adhesive with the spring contacts. Їх often stop for the connection of electrical wires with a span of up to 6 mm2. The spring-loaded plate allows it not to be turbulent, so that the luggage carriers get damaged under pressure. The pads are made from non-combustible polyamide, available in a number of color options.

Carbolite terminal blocks

For the purpose of connecting wires, in order to recognize significant interests, vicorous pads are pressed with carbolite. The basis of the building is significant heating (up to 150 degrees) and mechanical action. The contact elements of the viconanium of the visible tires are made of luzhenoy brass. The crimping of the stream-conducting veins is carried out behind the help of supplementary plates and metal screws. For some models, for additional insulation of the contact strip, a cover made of transparent impact-resistant plastic was added.

Important! The peculiarity of terminal blocks with screw clamps is the need for periodic revision of contacts. All gvinti is needed approximately once per day, contact may be loosened.

Self-tightening clamps

Shvidko otrimannya and nabula wide wide self-tight clamps that have appeared recently. The installation of such outbuildings will not require additional tools for the installation of darts. The design features of these extensions are in evidence in the housing of the spring contact plate. For vikonannya z'ednannya, it's enough to clean up and put a dart into a cell with small zusils. Two and more conductors, as well as at the terminal block, are released for the connection. A small amount of space is important for the inner diameter of the clamp, which allows the winding of the strum-conducting wires up to 2.5 mm2.

Special combs are used for the assembly of small and large electric circuits. Let's talk about what kind of terminals for connecting wires, how they stink, and how to make them up and put them on the rail with your own hands.

A terminal block, a screw lock or a terminal block is a special attachment, which is vikoristovuetsya for electrical wiring, it is richly safe, lower twisting. The stench is necessary in order to be able to tighten the cables of the electrical wiring, but at the same time do not harm them.

Photo - Installation of terminals on a DIN rail

The cable can be fastened without a middle under the head of the screw, or primus tightened behind the additional plate and the screw lock (stars and the name was given), for folded or delicate fastenings, the technology of blowing that screw is used. Even better, this attachment is important, that behind it, you can create a more hermetically sealed door, with no need for poor contact. For particular vipadkіv the cable can be inserted either into a special tip of the terminal block, which is then inserted into the terminal or an electrical cabinet, or attached to suitable tips, which are fixed under the head of the screw. Such electrical sources are called passers-by.

Photo - Klemnik earth-zero

Vidi Clem

Fallow type of construction, there are such terminal blocks for cables:

1. Flat;
2. Khrestovi ("twisting");
3. Hexagonal;
4. There are bolted, spring, screwless and screw clamps for cable clamps.

Photo - Vidi Klemnikiv

Gvintov_ self clamp terminals(Weidmüller, AVK Klemsan) are widely used in electrical wiring, pink boxes, for fixing contacts of an auto-battery, sockets, lighting up, connecting a group of lamps behind a singing circuit or telephone wires, installing an intrusive device (here it is necessary to put in special power blocks) thinly.

Photo - Self-sealing terminals

Screwed clamps sound vicorous for connecting lances to grounding, for example, to the programmable or mesh filter. Often, similar strum terminals are installed for the protection of loudspeakers in alarm attachments - acoustic systems, alarm systems, etc. Grounding clamps often spin greens and wink in by-button technology, There the stench is equipped with "teeth" - special entanglement of wires.

Photo - Earthing clamps

Video: different cleats

Design description

The most popular are the titles of bar'ern zatisknі klemniki. The stench is equipped with a row of short metal smugs, which are divided among themselves insulating ball. The skin wall of such terminal boxes is equipped with a bunch of screws; Such a terminal block itself is most often found in rozpodilnyh electric cabinets.

Photo - Barrier clamps

There are also universal terminals (PHOENIX CONTACT, Ensto, sv 15) for contacts that are installed on a different board, they have a simple design. It can be characterized by an insulating block, in which the metal tubes are connected with a pair of kilkistyu zatysknyh screws. The leather end of such a pipe is built-up to trim the dross, which is more convenient for wiring. Їх often vicorate for connection lighting fixtures or the creation of street visibility (illumination).

Photo - PHOENIX terminal block

There are more boxes with terminals (Nevski Plastex, TB) with a few screw terminals for one or two metal smugs, for example, ABB combs. Such a panel allows you to create a handy attachment, to spread the strum between conductors.

When choosing terminal blocks, it is important to open up the required block. This is one of the most important characteristics of supports. Tsey pokaznik to lie down in the cross section of your dart, let's look at the data for the AWG cable:

Description of materials for terminal blocks:

The next step is to indicate that the electrical tips are made from different materials, yakі need to choose based on your needs. For example, it is unacceptable to close the middays, aluminum cables different types spikes - you can cause a short hiccup. In order to make the dart creak, it is better to beat the same material, from which the stench is prepared. Let's say, the mid-wire cord of the miraculously tightened power terminals of the Wago company (Vago), for which the main material is mid. The same material is aluminum, stainless steel and their alloys.

Photo - Mіdni klemniki

Є universal carbolite terminal blocks, building stinks work with any type of wires, though the price is three times more for special ones. The warehouse is on the right, as it is necessary to connect the power darts. The leather material of the terminal may have its own working indicators, carbolite begins to melt at a temperature of 150 degrees. For extreme minds, just an indispensable ceramic terminal, good advice about the brand Legrand (Legrand), Degson.

Carbolite terminals

Installation of terminals on a din-rail does not take a lot of time to install from electricians-pochatkivtsiv. A lot of companies give their clients an extension with an automatic clasp or a “tongue”, just take a look at the catalog of the company, for you to know technical characteristics panels.

How to connect the terminal block to the DIN rail

For the cob, you need to open up a number of terminal blocks. The designation of the M6/8 terminal is to talk about those that we have in front of us with an attachment with a croque of a screw 6 and a width of 8 mm, which have proven simple mathematical calculations. All the terminals are simply squashed among themselves, for which it is necessary to put them on the right side one to one and then easily squeeze them to the clatter.

Now, having fixed the terminal blocks between themselves, having installed them on the rail, it is brought to the construction. electric darts. We recommend in the fall, depending on what type of cable and where to enter (on the board, light, stove too thin), mark it as in the photo with a color number. After the completion of the work, it is re-verified, if necessary, it is processed with paste in the form of corrosion (for example, if the block is standing on the street) that crusty.

Photo - Designation of terminals

Nezalezhnosti in addition, you zero darts chi nі, more importantly squeak їх іz zapobіzhnik - tse save you and your technique in the form of non-transferring voltage strips.

For the described variant of connecting terminals, you can buy a ready-made manifold comb, just click on the din-rail.

Photo - set of terminal blocks

Price overview

You can buy good terminal blocks in any electrical store in Russia, Ukraine, Belarus and other countries. Naturally, when buying in bulk, the price will be significantly lower. The variety is mainly deposited in the form of a cut and material of the terminal, as well as the firm-virobnik and the type of roztashuvannya (kutovі, buttovі thinly). The price for domestic outbuildings is richly lower than for imports.

For the butt, it is probable to take a look at how many pink terminals DEGSON are equipped with a screw with a 1 mm thread in different places of Russia and Ukraine:

Sales of terminals are growing both at specialized stores and centers, as well as at markets. Obov'yazkovo check before buying the certificate of quality of the series and GOST I will attach. We can recommend IEK (ІEK), ZVІ and ZНІ from three industrial analogues.