Electrician in a booth from decks. Installation process. Wired to a wooden booth. Retro spent in a wooden booth

]]> ]]> In the given hour, the zamіskom everyday life has more chasts wooden houses. Such houses have a lot of advantages: stench is made up of environmentally friendly materials, high pace of life, it is easier and more economical to scorch and even more so. However, electrical installation robots in wooden booth to develop their specificity and strength.
The electrician in a wooden house can be satisfied with richly zhorstkіshim vimog. Pochatkove zavdannya electrical installation in a wooden booth - the installation of an introductory (hoisting) cable in the form of a power transmission line support (LEP) up to rose shield at home. There are two ways of laying an input cable for the electrics of a zam_sky booth: repeating and underground (near the trench).

The second way of laying is more simple, quick and economical. For I will add redundant lines power supply to the zamіsky house self-supporting wire SIP grades of different cuts and different numbers of cores (deeply seen the tightness and number of phases seen by Zamovnik), special cable clamps, crepe anchors and more. The advantage of winning this dart lies in the fact that the tension of the cable carrying the cable is not required. However, the new way of laying the cable has its own shortcomings: damage to the aesthetic looking front part of the house, it is possible to damage the entrance cable with green plantings (trees, chagars), less durability.

The method of laying an introductory cable in a trench is laborious and expensive, but at the same time, aesthetics are saved sane looking at home, zapobіgaє posobіgaє posobіgaє posobіgaє poskodzhennya poshkodzhennya kabel zelenye zadzhennyami, zbіlshuєtsya termіnі service introductory cable. For the installation of the underground line of the electric power supply of the private booth, the armored cable of the brand VBbShv with a different number of conductors lived in that peretina (fallow due to the observed tightness and the number of phases). The cable is laid in a trench with a depth of at least 0.8 meters; cable” and then the trench will be covered again.
The input cable is used to supply voltage to the electrical shield, depending on the life it is distributed to all electric switches. At the rozpodіlchomu shields are installed: automatic vimikaci, outbuildings zahisnogo inclusion, differential automatic vimikachi, earthing and grounding tires and other attachments. Automation protects people, possessing all the electrics of the zamіskogo booth with a blast.
Rozpodіlnі electric shields at the zamіskom booth.

When performing electrical work at a wooden booth, sound the shields of the installation. Perevagu is recommended to be recommended vіdomih virobnіv such as ABB, Shneider Electric, Moeller.

Methods for laying power supply lines in the middle wooden booth

There are two ways to install a line of electricity in the middle of a wooden booth: overlays (wiring) and attachments (attaching). The electrical wiring is called open, the walls are laid on the surface, the booth is thinly laid. Electrical wiring is called attached, laid at the structural elements of the building: middle walls, overlapping thinly.
The simplest and inexpensive option is the overhead installation of electrical wiring. In this case, the work of laying cables and installing a switchboard, sockets and vimikachiv will take from two days to two days in the fallow area, the number of electrical supplies and the qualifications of the mains.
Overhead installation is carried out in non-combustible PVC cable channels (boxes), PVC corrugation (or metal sleeves) and is simply wired with a cable at a non-combustible sheath with fastenings.

]]> ]]> Laying the electric line of a wooden booth in PVC boxes

How to wall a booth with a flat surface (beam booths, booths with galvanized logs, lined with clapboard, frame-shield booths), installation is carried out in non-combustible PVC boxes. Boxes with straight-cut profiles with fixed caps. Installation of electrical wiring in ducts to ensure the following accidents:
- Wash cool wires;
-Strength of laying additional cables or wires;
- free access to wires and cables throughout the route and ease of replacement
- for the need to be able to create a vіdgaluzhennya on the road
The cover of the cable box can be easily removed and the additional cable can be added. With the help of the method, when re-cutting the box, a 30% margin is rotated.
Vyrobniki on this day proponuyut boxes of the same color: white, light brown and brown colors.
and structured tree: pine and mountain.

The soldering pins are placed in the soldering boxes of the same installation or in the middle of the sockets and vimics.
Laying wiring in boxes near wooden booths Laying wiring in boxes near wooden booths Laying wiring in boxes near wooden booths

Electrical installation robots at the wooden booth they let it in, so that all the cables passing through the walls and the overlap will be crushed at the metal sleeves.

Laying electric lines with a retro cable on insulators.

In this hour, it has become popular to lay oval wiring in a wooden booth with a retro cable (twisted dart) on insulators. Particularly dotsilnym є yogo vikoristannya in budinkah from a rounded deck. On the market of electrical installation materials, a retro-cable of Italian and Spanish manufacturers is promoted, a cable with a decorative braided "retro" GI Gambarelli, Italy. Possible next color options: white, gold, gray, black brown.
We propose the optimal way of laying electrical wiring in a hutch-blocked booth - a combination of laying in cable channels (boxes) with color and texture of wood and a retro cable on insulators. With such an approach, the main (horizontal) lines are laid in the cable channels of the skirting board or at the stele. Drops and connections to vimikachiv, sockets and other electrical installations are connected with a twisted cable at the decorative braid on insulators. The soldering sockets are vibrated in the middle of the cases of sockets and vimics, or in the boxes of the box of the outer installation with the color and texture of the tree.

Electrical installation at a wooden house in a direct way on the shackles

PRACTANDED CABILE VIDKRITIM METHOD SERVICE SODIVE IN TO BIPADKA, Yakschko Protdannnya Lynіne Ekletpostachannna in PVC boxes, not instructing ETTECTICS Інтерь'Ру, Zdіysniti folded, and ііді і іідовильний (right, Elektrick Budinka from Otilіndan ) or behind the bazhannyam of the deputy. The soldering pins are placed in the soldering boxes or in the middle of the sockets and vimikachiv.
Laying wiring on brackets at wooden bollards Laying wiring on brackets at wooden bollards Laying wiring on brackets at wooden bollards

Prihovane held electric line at the wooden booth

In wooden booths, this type of wiring is installed in metal pipes (valid up to PUE p. 7.1.32)
Attachment installation of a line electrician in a wooden house is a more laborious, long and more expensive process. Prote, with a look at the design, privablishiy.
Mustache main lines of electricity in a wooden booth are fixed at the metal steel pipes at the crossroads to the vlashtuvannya (pіdshivki) pіdlog that stel. Pidyomi to the sockets, vimikachiv and luminaires are installed at the vertical technological openings of the walls.
Pochatkov, even more important task for the Zamovnik - it should be used for roztashuvannyam elektrospozhivachіv v budinku (with їх geometric bindings) From the plan for the expansion of electrical installations, a plan is being prepared for the drilling of vertical technological openings in the walls of the remote assembly of electrical installation robots near a wooden booth.

Drilling of embedded openings at the walls of the booth is carried out in the workshop at the stage of opening the booth, or in the process of selecting the booth directly at the place of installation. As a rule, this method zastosovuetsya when laying electricity in a booth from a galvanized well. Switching of wires and soldering conduits are vibrated in metal soldering boxes or directly in sockets and switches.

For the installation of sockets and vimikachiv (before previously assigned geometric bindings), open the socket outlets for installing the mechanisms of sockets and vimikachiv. For whom it is necessary to know a series of rosettes and vimikaci, which are installed, so that the installation boxes for different series can be different types.

]]> ]]>

Apply to the installation of electrical wiring at the booths from a wooden beam.

Respect that Vikonan's electrical wiring is corrugated pipes, yak, on the vіdmіnu vіd metalorukava, sucіlna, so that it was not crushed from the burnt smog. Therefore, localization building is hermetic. Assigned to that number for the water and gas pipeline.

Laying in such a pipe is satisfying BNIP and PUE. These companies, on which PVC corrugated pipes are present, will be rolled out in concrete screed so that it is honed with non-combustible material.

Wired to a wooden booth

]]> ]]> The article "Electrician of a wooden house" spoke about the simplest wiring option, which will provide you with maximum safety with a minimum of wattage. Functionality should be placed on the top of the list in the descriptions. Aesthetics enter another plan. Obviously, it is possible to cut the wiring as carefully as possible, so that it will not fall too much at the vіchі. But not everyone needs cable channels on the walls.

Deyakі namagayutsya zasosuvat kolorovі elektrostanovlyuvalnі virobi, vikoristovuvat boxes of brown color or wood, but, unfortunately, the selection of such virobіv is small, the quality is far from being reliable, the vibrators do not provide the necessary assortment of fittings, fittings, turns. Without them, carefully install the cable channels in a foldable way, through the swell up to the tree, swelling and shrinking, the sticks expand, the ducts shrink slightly - the wiring stops looking neat.

Є y zowsіm neruchnі vipadki: yak, for example, put the boxes on the broken walls of the decks, on the walls sheathed with a fashionable blockhouse at the same time, or upholstered with a shaped board "overlap"? Looking for cable channels? Just nail it to the walls with shackles? However, the non-leather cable looks aesthetically pleasing.

Most VVGNG cables can be insulated in black color, NYM - gray. How is such a “color of din” to match the color of a tree? And how about the situation, how did you instruct to lay a piece of cable once? In a modern house full of electrical appliances, a lot of cables laid in parallel can reach a few dozens in places! Don’t forget that the possibility of laying cables without a middle ground without a mechanical twist can be looked at quickly normative documentation. So, SP 31-110-2003 allows for laying on a solid foundation without lining only “with a single cable with middle conductors with a span of no more than 6 mm2, so that it doesn’t rise all the way.”

Otzhe, it is not possible to run two cables in a row? Why can't you fasten them with one staple, how is it customary? And if you want to conduct them on the singing station one type of one and there will be not two such cables, but five, ten, more, then what will the wall turn into? Ale, the PUE requires the installation of wiring at residential premises “in electrical skirting boards, ducts thinly” (P. 7.1.37). Chi can mi rahuvati "i etc." allowed to carry out wiring without intermediary cable along the walls or rollers, tab. 2.1.2.?

Ale in the distribution “Select the type of electrical wiring, select the wires and cables and the method of their laying” PUE is about electrical wiring in a flash, but in goal. 7 about electrical wiring at special premises, up to which they lie at, incl. that living accommodation. In this manner, obviously, the following interpretation of the “i.t.p.” is not like laying cables directly on the walls, but laying in electrical hard and flexible pipes, metal hoses ... That is the cables, laying on the walls possible mechanical failure.
Problem electrical installations.

Assortment of sockets and vimikachiv for vіdkrytoї wiring arcs. Most of the reputable virobniks add even more for the found series. These series do not have a lot of handy “lotions”, like in the series of the middle and high price range. For example, there are no programming dimmers, cross-widths that allow you to light from three and more places, there are no different timers. The color of the din of virobiv has been trimmed, the material that is stagnant is inexpensive plastic.

]]> ]]> If you want the quality of virobiv from the reputable virobniks of the temple, the stench is far from being able to please the relish of a squeamish purchase. From what is presented on our market at once, I can name the series "Etude" (produced by the Schneider Electric plant in St. Petersburg), "Wessen" - also recently arrived by Schneider Electric, "Elyo" - a large independent Swedish company, sold by Schneider Electric, Simon ( Spain ) Kopp (Nimechchina) - two more to be found, and a number of others. There are Turkish and Russian sockets on the market, and vimikachi for proper installation, but it is worth remembering that the wiser series are supplied.

Widely in our country Legrand and ABB products are not allowed for outdoor installation, but there are special ones that are installed in water and powdered applications. True, most of the assemblers have in the range of pidyomnі ​​boxes (sing out the fringe of colors), which allow you to mount the slabs for the attached installation in the cable system, but also look at the wooden walls even more quickly. Well, it doesn’t suit everyone, so that for a perfect installation, they protrude far into the walls, which makes them more comfortable, especially in the areas of passage and arranging the placement of furniture.

In such a rank, we believe that the electrical wiring is far from reliable, it can inspire the whimsical relish of coristuvachs. Ale to the attached wiring according to the structures that are burning, the Russian regulatory documentation presents even more zhorstkі vimogi, which are sometimes created by the unknown. There are only two options here: laying cables in deaf metal boxes or metal pipes or in non-combustible plaster, as it is the responsibility of removing the cable from the sides with a ball of at least 10 mm (Table 14.2 SP 31-110-2003, PUE: Table 2.1.3). . Such a zhorstka of the vimoga PUE seems to be unrecognized, because with a glance of the nefahivtsya, I turn the houses into a “water supply” as a kind of darts to go.

Well, I know that I didn’t fall for the thought of breaking the garn of the lining with a ball of cement or gypsum. Sounds blame the misunderstandings of how much they could. “What can we do with the cable at the insulation, if we don’t subdue the mountain, we’ll protect it with modern automation, we’ll lay it inconspicuously from the shield to the outlet?” - so the deacons "fahivtsі" in the form of electricians mumble, scribbling at their impossibility.

The stench stretch the cables along the overlaps in the corrugations, shove the drіt under the plinth, howl їх від “cash out” windows and door frames, vtovkmuchyuchi unidentified client, scho itself so and work. Prote, I'm ready to take a look at two unfriendly developments in the scenario, such as, perhaps, the retailers of regulatory documents were cherished, installing such hard vimogi.
1. Grizuni. Bears and squints can appear near the ceilings and walls of wooden houses. The “companions” of people are not welcome anymore, and I can’t help but love the grizzly plastic insulation of darts. I happened to see the walls of the dart, the isolation of which was seen for a few meters. Vaughn carried on her face the traces of her teeth. Mіstsyami іzolyatsіya bula vіdsutnya zovsіm, i short chirp could become like a mit. Navit, as if the automatics were shutting down, it would work without a hitch, in the time of a short flicker, for a few seconds, it would become stronger, the building’s wooden saw, rub, shreds - that little shvidko-sealed material accumulates over time at the walls and ceilings.
2. The tree, as it seems, "goes wild". Changes in moisture are added to the price. All of us stuck to the door, which wedged, and vіknami vzimka and hinged, if the water level increases again. In addition, the budinki are skhilni to the deako's fall. The cable can have unsafe voltages, which can lead to some damage or a shave. A further development is already under consideration at p.1.
[Working moment. Laying cables at steel trays. The wall is sheathed.] As the cable of the premises has a non-combustible middle, then there will be no further expansion of the fire. The maximum, chim mi rizikuєmo - will not be light in okremih primіshchennyah or stop pratsyuvati one or a sprat of sockets.
Deyakі assemblers vikoristovuyut for prihodannya laying of cables metal hose, vvazhuchi yogo gnuchka metal pipe. However, in the normative documentation, nowhere is the use of a metal hose like a metal pipe. I think that it is explained by him that he is not “deaf”. The strengthening is secured with a bavovnyanoy thread, which miraculously lifts the mountain (type RTs-X). Bazhayuchi can make an experiment - a twisted amplifying cord and a light igniter. The result of the development of all sumniv. The metal hose is also produced from asbestos indentations (RTs-A). Ale vin extensions are already insignificant. At the sale, it was important for me to know a metal sleeve with an asbestos thread only of a large diameter.

In this rank, it is unacceptable to bend a metal hose for tethered cable laying in combustible structures with proper regulatory documentation.
How wiring can be vikonan "theoretically" understood. Ale yak dotrematisya such zhorstkih vimog in practice? In this article, I will try to focus on the technology of viconnance of these simple robots.
Option 1. Combination of cable channels and electrical installation for wired wiring.
The main lines in this variant are laid in the boxes of the vzdovzh stele or under the plinth plinth. [Prihovane roztashuvannya vymikach, podvedennya cable in the cable channel] V_dgaluzhennya to sockets and vimikachiv vykonuyutsya a low cable duct, the end of which is closed with a plug. Electrical installations are mounted in metal sockets. Under them, in front of them, an opening with a crown on a tree is burried. Such an option, which allows you to add cable laying and sockets and chemicals for a fixed installation, allows you to expand the range of the remaining and change the depth of protruding parts indefinitely. As an option, it is possible to place the mains in the external premises, where aesthetics are not so important, drill a star in the wall, lay a steel bushing, install a metal socket and viconate, install sockets and vimics on the walls of the "front" room.

Option 2. Attaching the mains and wiring to the cable channels.
[Cable channel on the support.]
The main lines are laid at the crossroads. For this unique vicor, metal pipes are used. Through the need to win, turn often beat the copper pipes, the price of which goes off the scale of all reasonable borders. Mikoristovuєmo deaf metal trays with caps [Cables in metal trays], specially designed for metal. Promislov_st releases such trays of various roses. Dozens of cables can be laid at the wide one. Trays are made from galvanized steel. The tovshchina of the walls is not important, because for medium cables, span up to 2.5 mm2, this parameter is not standardized. It is too late to tighten the cables into the corrugation or to protect the places of turns and possible contacts in the insulation of the cable with the most metal edges of the corrugation or the chlorine-vinyl tube. Laying metal trays is not an easy operation. Necessary chastkove pіdіzuvannya beams perekrittіv z distant їkh polennyami, obhіd load-bearing structures, cleaning of sharp edges, laying ends. For vikonannya all these operations, you need a different tool and beginners of iron robots. The trays are creaked between themselves with rivets and bolts and nuts. After laying cables in them, grounding is metal structures. For this purpose, a grounding wire is stretched, screwed to the skin part of the tray with a screw and a nut. To the tubes, the grounding wire is fastened behind the help of steel clamps.
Vіdgaluzhennya to the rosettes and vimikaіv vykonuyutsya through the opening with steel bushings at the ceilings of the sound. plastic box. There are no special problems on the equal walls, and the axle on the deck needs to be fixed for the installation of cable channels and electrical installations. In order to make such a support from a front-worn and polished board, they mark it in front with a special tool, which was called a deboning among the old masters. There is no way to sell such a tool - you can make it yourself. The results can be seen in the photo.
Option 3. The wiring was reattached to the booth that was broken from the decks.
This change is the most complicated and is given to the unimaginable unacknowledged maistrov. The highways, like the other option, are wound in overlaps, in metal trays. And the axis of the situation is folding. Let's forgive the most obvious looking placement of vimikaci. Because stink, ring out the handrail from the door, you can hook it up with the door frame. Prote, it's not enough just to take a wire. It is necessary at the end of the decks, to vibrate the end of the benzo-abo electric groove, in which a metal tube is placed. In this way, for the sake of victoriousness, the posture of competition is mid. Because the mid-range pipe is beaten up too much, then it doesn’t cost a lot of money. A wire is laid at the pipe, after which it won't go away "for a job" for an additional pipe bender. At the wall, drill with a crown an opening for a metal socket. The groove at the end of the decks is closed with a large-diameter opening with a socket. All the vines are due to be smooth, otherwise the middle tube will pass the wire. Naykraschi - vykonannya equal maidanchik under the frame of the electrical installation. Otherwise, vimikach will become skewed.

With sockets, the situation is folded. It is not logical to place more sockets there, if it is conveniently coristuvachev, it is more illogical to place more sockets with door openings. The axis is one of the ways: for the introduction The lines of the old lamps and vimikachiv converge here. The possibility of control and maintenance has been transferred.] a groove is sawn to the socket in the lower decks. At the new one, a pipe is laid from a drotom. In addition, from the boards of the required width, a stub is prepared. Її shchily zaganyat at the groove, sawed off and polished. Bazhano, before installing, cover the plug with joiner's glue. All how much that unevenness is puttied with putty on wood in the color of the village. After hanging the putty, sanding is repeated. At the end of the board, you can draw little fibers of the deck - even after covering the walls with varnish, or the leakage of the cable will be practically unremarkable.

A similar job will require high qualifications, various skills and tools. For the preparation of the month for one point, the master has less than half a working day, the robot is highly valued. Ale beauty, as it seems, will require sacrifices that chimalih vitrat.

Slid unikati roztashuvannya overlaps and walls of soldering boxes, tk. imovirno, [Blind trays in the deep space] in the process of operation, you will need their maintenance. So, the space for soldering may be available. It is possible, of course, to run a small cable from the shield to the skin socket, otherwise it will lead to an unbelievable increase in the amount of material. The sockets can be divided into groups according to the applications and connected with a loop in reasonable boundaries, you can destroy the sockets, install one more and unsolder the socket mechanism. Nebazhano only soldering and looping the sockets, seeing the sweat, post-invention: obіgrіvachі, pralnu that dishwashers, electric stoves, boilers too. In these vipads, pull the darts without a middle in the shield and protect the lines with machine guns.

Naturally, I especially respect the next step for the selection and installation of automation. The shield of the great hut with galvanized wiring can have dozens of elements. Tse already know to us the automatic switches and extensions of the power supply, as well as surge arresters, interchangers of overvoltages, phase switches, systems for boosting backup power, too. Often, in order to expand the head shield and change the wire cable, add-ons, overhead shields are installed in cottages. It also allows you to change the winding of the cable and make it easier to control the energy system of the booth.

Do not forget that the main method is to defend against the defeat electric jetє zahisne grounding. To that, in the obov'yazykovom order on the dilyantsі maє buti vykonany contour re-grounding and the whole rozpodіlna merezha vykonuєtsya triprovіdnoy. The choice of the grounding system is determined by the skin specific type of fall into the ground.

Retro spent in a wooden booth

retro wiring at the wooden booth "Retro" and "vintage". Some of the words of the building viklikati zavmirannya hearts of the singing category of people, endowed with admiration for the sense of beauty. Qi people are the last in everything, so the retro wiring in their eyes is especially garniy relish that originality.

And as for the reminders, for example, from a galvanized deck, and internal improvements on the inside, then the retro wiring on the rollers will definitely look the most aesthetically pleasing. Even a plastic cable channel in such a situation is not strongly attached to the wall through the grooves between the decks, and the installation of the cable behind the help of the bow behind the structures that burn up is fenced. About the frowning sіra and the everyday corrugated pipe, it was closed.

]]> ]]> Come out, choose retro-wiring for installation in a wooden house with a lot of practical priming.

Otzhe, what is retro wiring? Classically, so on the cob of the 20th century, it was wound with two single-core, bagatodron wires, twisted in a spiral. The insulation of these wires was single, and the stench creaked on the supporting porcelain insulators (rollers). When the boxes were not closed, the wires were wound up twisted, as if they were being insulated, so that the ends were not washed away.

Retro wiringZolozumіlo, such electrical wiring does not in any way match modern fire extinguishers and electrical safety. Therefore, on this day, you can only vikonatize the imitation of the old style, the stylization of її retro.

For these purposes, electricians buy small plastic or porcelain insulators and call single-stranded darts for an additional drill into a hot bundle. Fallow in the presence / in the presence of grounding, the harness can avenge two or three darts. During installation, the harness is simply pulled on the insulators, screwed to the wall or steel through the equal gaps. In front of the insulator, the next day, it’s better to put on small clothes before the hour. heat shrink tubing(HERE) what to go for the color of the dart. Ensure the tube is suitable for installation.

But still, independent winding of the dart is retro - for those who are willing to spare. The same kind of wire, isolation of some kind of matimé index NG (non-combustible) and LS (with low dimovitions), it will not be easy to call in a retro harness. Therefore, it’s better to have a special retro draft of the factory’s vikonnannya, special certifications for installation at the warehouse for electrical wiring.

Retro wiring It's a little bit to walk around, that the variety of such a dart is already established on the territory of the Russian Federation here near Pdmoskov'ї, but in the stores of our country, the Russian retro wire is still not clear. Vlasne, and from abroad with a retro wire, the situation on the market is not richly beautiful.

Conducting fittings for the installation of electrical wiring in a retro style sound must be done in Italy. You may not be able to go there on your own, but your post-commander, as much as possible, mother right with the Italians.

For example, the firms Fontini and GI Gambarelli produce not only retro-drills with 0.75 - 2.5 square meters. mm. with two or three wires, alley and rollers for installing a bolt, as well as sockets, turning vimikachі, vіdgaluzhuvalni boxes and blocks to place the socket and vіmikach on the central stand.

All elements of the electrical wiring are stylized as old fashioned, their material is porcelain, and vikonan stink with the requirements of all fire safety standards. Sockets In a word, you can fix the retro electrical wiring, which will provide the most important security guards.

There is only one "ale". The bay of a retro dart of a zavdovka 50 meters can easily cover a thousand rubles. Vimikach or the rosette cost two thousand rubles a second. One video is about 30 rubles (and how much money is needed for a whole house!). Tobto, retro conduction will not be cheap for lovers of old fashioned and esthetes, and you need to remember about it.

It is worth noting that the products of the Salvador company, which also specialize in the manufacture of retro cables and accessories, but which have expanded their manufacture in China, do not go beyond the price of their Italian counterparts. So the economy is hardly possible.

Regardless of the fact that retro drіt is coming, the structure of the skin will live forward: richly cut copper in the underwire sheath made of PVC plastic compound, covered with a piece of non-combustible seam. The color of the oval PVC leather sheathing lived in accordance with the PUE standards: black, brown and yellow-green.

The color of the oval seam coating is the chain of special relish for the design. It is worth considering whether the color of the tree should be golden or beige. And who knows that the retro wiring is also an element of the interior, and it is to be seen on the aphids of the walls behind the color - buti, for example, white and black flooring, just anthracite.

Retro wiring According to the color of the wire, choose the color of the housings of the sockets, the vimikachiv and the electrical boxes, as well as the color of the insulators (rollers).

Through those that retro drіt is more expensive, and also to those that have a maximum area of ​​2.5 sq. m. mm., don’t slid all the wiring to the retro style itself. Entry cable If you don’t fit into the wild vintage style, you will need to put it in the pipe. And if the rest does not fit into the interior, you can hide behind the skin.

At the pipes, it is possible to lay the cable to tight stationary priymachiv, for example, to electric stove or a water-heating cauldron. Replacement of pipes can vikoristovuvaty plastic cable channel, pіdіbrany pіd kolіr sіn. Like a cable for stationary electrical receivers, you can twist the splendid VVGng, even though you won’t be able to see it all the same, and until the retro style of the wines, you won’t be able to look like a dream.

It is not uncommon when installing retro wiring in wooden electric cabinets for the weather with the master or the designer, they know one more way to save on an expensive rod. That part of the wiring, like going through the entrance shield and living in groups, can be wired with a special cable under the sheathing of the steel in the pipe, or just along the wall in the box. Then go out, that without a middle retro drіt go only from the vіdgaluzhuvalnyh boxes to sockets, vimikachiv and lamps. It is not uncommon for this to be enough and enough, the most important part of the wiring is to pass along the walls vertically or go to the stele to the lamps.

There are two ways to get rid of retro droids in the boxes:

1. Irradiate and insulate extremely twisted. Bagatodrotians lived easily twisted, and if you don’t save on solder and don’t forget about the flux, you’ll be more expensive.

:
For the cob, let's be significant - I'm not a competitor to you - I'm not an installer and I don't work in electricity, I can get out, because I can't myself. The only one, why I’m ironic, because I’m bringing the bajannya of your potential zamovniks to fence in the broken decks of EU mills, recognized for the hoisted installation, for which to drill dozens of meters of canals and dovbati empty in the decks. Only for the sake of it, to click with a vimikachem ... Do not doubt that the risers can be made with forges. And what work, if I need a group of sockets in the middle of the wall?

People, like budinki, want to be safe and secure. You can safely work and open the wiring, but there is a problem with getting the cuts of the decks and lowering (pidyom) to e / installation. virobiv. You can overcome the problem of prosthetics of the lower decks, the installation of high plinths from the boards, wide preparation and decorative elements that allow you to lead verticals. However, the variability of similar works in connection with the cable channel does not look like "t-layer", it is connected with wired wiring, so it does not change. It is also necessary to bring power lines up to the mark. Install sockets when attaching wires, whether it is a point of the perimeter as much as possible. Single exchange - installation height 1-2 deck in UCHP.

Is it just a creaking pipe (not a corrugation) or a metal tray? Particularly in the months of coming up to the present virobiv and kutovyh transitions for jambs and іn. (I just feed, maybe you give everything in the midyak 8-)

Metal scraped Wimogami PUE. Previously, they victorious with t.ch. that mean, more technological materials appeared at the same time.

And the transition itself is zhorsky? With a chainsaw and a kind word, you can work a hollow behind a jamb, but if the transition is not flexible, be it a cut and a place, the shrinkage does not collapse into the transition point by 3-6 cm down, from the plane of the footlog to the height of the window

You do not understand the shrinkage process correctly. Ale, the crossing is slinky. Until then, I don’t undertake to work the houses, as if I didn’t stand 2 rocks.

I know what to sit, but I don’t need flooring, as if the normal beam from the boards of chamber drying and yoga were taken normally. Ale yoga so do not tear and do not twist like a deck.

Correctly picking from the deck of budinok is also catastrophic not to twist. Likewise, the pins were placed in the order of checks, suvoro entrusted with possible cuts, the cuts were correctly and hourly oxidized. Often, we work for ourselves, more often, that at once you can vikonati pidyom to vimikachiv with a smooth vigin.

OK, for me, let's say a deck of 32 cm (before shrinkage was 8-)), at the perimeter is close to 18 -20 cm width of the overlap of the decks, the entire groove of the groove is at the end, it is 16 cm. direct - you need to turn on your clip more lower on the pivkolody. Or another turn from the axle to the adjusting box. What's up? Mid, metal, corrugation?

Who said that you need to go into the box of obov'yazkovo from the axis of the groove? In the skin, there is a different variant of the approach. You can't see the template here.

Usі photo zі statti

Everyone can see that the wood is fast asleep and dosit actively burn. So, whether it’s budіvlі z timber or decks, navіt for the mind seep out of the material with flame retardants, all the same, they are in the group of promoted fire ailments. The axis of why, during everyday life, on an important mission, stand food for fire safety and, zokrema, under special respect - electrical engineering robots.

Electricity supply for a wooden house

The head of the safe operation of the electric power house can be hung on the back of the paper, so everything starts from the project.

At the stage of yoga expansion, solutions are accepted:

• Connecting to the central electric meter.
• Organizations introductory annex.
• Method for laying electrical cables.
  You can use:
  1. Wired in a broken booth from the decks.
  2. Vіdkrita, roztashovana over designs.
• Methods for the installation of electrical appliances:

1. Vimikachiv.
2. Light regulators.
3. Sockets.
4. Svitilnikov and others.

Respect!
Do not lose the qualifications of an electrician, rather do not take on the development of the project and its implementation with your own hands.
Request fahіvtsіv good-quality firms and for designing, and for installation of the electric house, so that you close the power supply for the safety.

For those who are able to build electrical installation work independently, you will need this material as an instruction to a step-by-step completion of the task.

Connecting the electric cable to the booth

There are two ways to connect to the power line:

1. Let's look at the smaller stained glass and swidko zdijsnenny. For this vicorist, a self-supporting cable with a rosewood kіlk_styu lived with that їх peretina.

See you!
Rozrahunok pouzhnostі autonomous elektromerezhі vykonuєtsya z urakhuvannya planned navantazhennia, yak lie in the amount of electricity in the house.

1. Underground is more expensive and laborious, but there are a number of advantages:
   • Laying a cable under the ground will not damage the exterior of the building.
   • At this point, the cable is nadіyno thefts vіd poshkodzhen, scho prolonging the term of service.

For underground laying in the line of wooden houses, a power copper cable should be twisted.

See you!
The project of connecting a private house to the central electric power supply line for the provision of public services with a local energy supply organization.

Introductory attachment

By the reception of that distribution of electricity for specific helpers in the middle of the booth, it is installed through the entrance attachment-rozpodilny shield.

Yogo is installed at a safe place from secure free access at any hour to possess it:

• Automatic vimics.
• Aparati of a good connection.

Respect!
Introduction to the booth power cable zdіysnyuєtsya through vbudovanu metal sleeve.
When rozvedennі elektromerezhі prismіshchennya in mіstsyah passage of the cable through the walls and overlaps also installed zhorstki metal sleeves.

Vvіdno-rozpodіlny shield is guilty of buti maximally stealing from contact with wood, so it is necessary to place it near a special metal shield. The number of "automatic machines" and other outbuildings is divided into such boxes.

Internal breeding

Once the electrical panel is in place, you can proceed to the installation of the internal electrical wiring.

As already mentioned, the electrical wiring to the booth from the galvanized deck is wound by one of two essential methods:

• Vіdkritim.
• Let's attach.

Vіdkrit conducted

The first way is worth more safely in case of burning, before that the price for such electrical work is much lower.

At open wiring yoga cable is laid without a middle on the inner surface:

• Stin.
• Partitions.
• Stele and other designs.

Enhancing the aesthetics of the modern looking electrical wiring and for the additional protection, they are at the self-extinguishing boxes. Current selections of similar products offer a wide range of selections of various design solutions:

• Different color.
• Imitation of the texture of the village.

In such a channel, the electrical wiring is camouflaged in a booth from a galvanized block through the even surface of the walls.

Prihovane held

The method of laying electrical wiring in a wooden house is unsafe, laborious and expensive. Ale z aesthetic mirkuvan rich who schilyaєєєєєєєєєєє himself so mount elektromerezhu at his booth. To that, it’s important to rozіbratisya, as if I’m attaching the wiring to the booth, broken from the decks, as safe as possible.

Important!
I'll add a smut rule attached electrical wiring at the zrub - turn off the contact of the darts with the wood.

On the right, in the fact that the problem can become not only a short flicker in the merezhі, but also sound, what can be heated under the influx of high tensions, the metal haircut under the ball of insulation.

• Cable channels.
• Trumpet.
• Corrugated sleeves.

The rules of the attached event are as follows:

• The laying of the main lines of breeding with the attached method is wound in parallel with the picking of the cut.
• Pidyomi to the fixtures of lighting, rosettes and vimikachiv roztashovuyutsya through preparations open.
• The middle overlaps of the darts are laid in non-combustible plastic pipes in such a manner that the stench did not give way to mechanical infusions.
• Wired to a booth from a galvanized deck is guilty of being carried out with a rozrahunka її natural ї shrinkage. All channels and sleeves with wires are guilty of buti protection from the vice of dry decks.

І attachments and vіdkritiy methods of breeding electric darts to waste their shortfalls and gains. Due to this, there are often combinations of ways to install the elements of the electric supply of a wooden house.

Select an electric cable

To ensure that the electrical wiring in the booth, which was broken from the decks, was effectively safe, choose for the electrical supply a single type of cable with letters in the marking:

• NG, which means that the mountain is not supported.
• LS, then there may be a decrease in dimovidіlennya.

Now, about pererіz and kіlkіst lived near the wires, so that you can lie down in the middle in the presence of tightness, that you are accustomed to the electric power.

• For lighting, it is laid three-core cablesіz retina 1.5 mm square (3x1.5).
• A 3x2.5 cable is required for the distribution of a sub-socket.
• Cable for electric stove less than 6 mm2.
• To the point, to live the block of sockets with 4 points and more dodatkovo nothing is connected.
• As a whole, the following equipment is connected: a circulation pump for scorching and a water supply pump.
• Also, a scorching boiler and a water heater are connected to the obov'yazkovy autonomous connection (for such needs, or for the supply of gas).

Rozrahunok elektrozhivlennya opalyuvalny obladnannya є foldable milking.

The back of the head is relieved by the pressure of the possession (boiler) on:

• Appointment obsyag primіschen.
• The temperature regime is required.
• Spend heat through the construction of the booth (pillars, windows, doors, walls and ceilings).

Tsikavo!
Varto signify that the coefficient of thermal conductivity of a galvanized deck is even lower for paving with stone and concrete.
Therefore, the heat loss through the walls of the pit will be minimal, especially in that case, as the caulking bula was crushed with a lot of special features of the process.

Razrakhovuvati on povnu I'll burn safety living from the village is efficient, uninterrupted work Electricity is possible less, if you have completed the instruction:

• On the choice of cables and cable channels for a wooden booth.
• Installation of carrying out according to all the rules that is required before the project.

Please!
Upon completion of the electrical installation work, it is necessary to check whether the insulating sheath of the cables is not damaged.
For whom to conduct a vimir support of insulation lived.

The electrical wiring in the booth from the galvanized deck is due to prophylactic re-checking for poor insulation at regular intervals of three times, to turn off possible flickering at the fence.

grounding

Appearance near a wooden house housed to a dry fire, a blisk of water and a ground loop is another important part anti-burner zakhistu. And the grounding here is not only electrically controlled, but metal channels and trumpets, with which darts pass.

Visnovok

Now there is no more guessing that all the work is carried out with the help of modern technology, safety and with the best materials. The possibility of twisting the cable for additional insulation can be turned off, today there are no options, for the help of which it is possible more and more securely to put two darts under the pressure.

In the video presented in this article, you will find additional information on this topic.

How to prepare exit points before installing electrical fittings? Tse nutrition should be brought to the skin electrician at the time of installation of communications at wooden booths. Chi tse zrub, tsilindrovana deck, round timber or block house, there is only one problem - there are no even surfaces that are suitable for installing sockets and vimics, vtim, and lamps. wall sconces. There are two ways to prepare maidanchiks for points: overlay on the deck . Let's talk about the peculiarities of stosuvannya skin of them.

Long-term fates are the only solution to the problem. This method is called in a different way: saw cut, stochuvannya, stubbing, milling thinly. Polyagaє vin at the one who, at the place of the point of exit, vipilyuyut a dilyanka for the form of the world, which shows vimikacha or rosettes.

What is important to lie to a robot:

Squeezing the deck is absolutely non-professional for an electrician, having taken up such a job, it’s also risky to wrongly zip the deck. That’s why the carpenter is engaged in vipiluvannya maidanchikiv, who knows how to work with a tree and to grind everything neatly.

It is important to lie what to inspire front desk specialist you can allow a hat like cracks, chips, not a new shape. Wood is a non-transferable material. І more - the mounting box is incorrect in the photo, looking at the accessory sockets for materials that are lit up.

As soon as the master gave the booth to move the vimikach or the socket in another place, there is an unacceptable surprise on the new check. If the body of the socket is taken away, the propylene will be lost at the deck, as it is impossible to burn. To grab something, to bring a picture, or to put a closet, other furniture.

If you are planning the preparation of the Maidan as a carpenter, add additional working days to the term. Therefore, up to 30 quills are needed to prepare one point at the booth.

Method easy installation rosettes and vimikachiv near wooden houses near Russia have begun to stop up recently. Deck overlay - ce attachment for the possession of a point for the exit of electrical wiring of a hard-wired and attached type (with a 68 mm gap). It creaks up to the wall and firmly lies behind the rahunok of the lower part of the hollowed out part, which fully reflects the diameter of the deck. The upper part of the overlay is a straight maidanchik for the installation of vimics, sockets, rosette/switching boxes and lamps, sconces.

Features of the technology for mounting the lining on the deck:

You can install it by an electrician. Special carpentry tools are not needed.

For the preparation of one point pide 2-4 whilini.

When installing the lining open type the socket or vimikach can be moved to another place. The installation of our padding on the deck is not vpline on the surface of the wood, it does not capture the aesthetic characteristics. In case of transference, small openings are opened for fastening, which is easy to lay down.

Choice of overlays with dielectric plates move the safety of electric wiring to the open type. Sklotekstolit with a thickness of 1 mm, exactly matches the size, sharply closes the perforations on the basis of Legrand Quteo plastic sockets, and in the series

Yak bi was not beautiful, the tree was like a budіvelniy material, but there may not be enough songs. Tse does not mean that yoga is not varto vikoristovuvaty, even wood is a truly miraculous budmaterial - minty, supple, warm, environmentally friendly, natural. Just under the hour of everyday life, it is necessary to take care of all possible ills in order to neutralize them. What kind of wiring can be in a booth broken from decks? The axis of the wines, the lack of a tree - do not stick until the fire. A lot of unique monuments of wooden architecture perished through it. Sometimes sleep is due to reasons independent of us and incompatibility. Ale, even more richly, blame yourself for the wrong conduct. So that it doesn’t become dashing, it’s necessary to take a step back about coming in. TOV "SeverBudLis" not only to build wooden houses, but also to carry out all the internal work with the improvement of the necessary powers.

Electrical wiring in a broken house from the decks

Life can be not only comfortable, we will add it warm, the houses can be safe and secure. In a different situation, it’s not only risky to spend all your time, but to spend your life, for example, with a rapt fire at night, if all the members of the family sleep. Electrical wiring in a house built from decks behind the PUE can be carried out in a closed and closed way. work from electrical wiring to become advanced folding, so it’s better to entrust them to professionals. The company TOV "SeverBudLis" has a great opportunity to build wooden houses with different technologies. That's why we'll do the installation electric lines for your booth. With this, we can suggest a few options in your opinion, from which you can choose the one that pleases you the most.

Wired in a broken booth from the decks

At a wooden booth, it is possible to carry out electrical wiring only at a metal box. The main lines are laid in steel or copper pipes for reinforcement and underlay. To the elements of electrical installations: sockets, lamps, cables are pulled by vertical technological openings in the walls. In this situation, the zamovnik is to be blamed for exactly this, where all the elements of the electrical system will be placed: where lighting fittings, vimikachi, sockets will be installed. In another situation, it will not be possible to transfer the wiring without damaging the integrity of the walls;

Widkrita electrical wiring near a wooden booth

If the emphasis is on functionality, and the aesthetic warehouse is put in the background, then in this way it’s better to victoriously open the wiring. The cable is carried through a special non-combustible box, a corrugated tube with a vinyl or a retro cable, modern today. You can choose the color of the box from the classic white to the one that imitates the color of the tree. Vіdkrita electrical wiring in a wooden booth is mounted in rows for two to ten days, fallow in the square of the booth with a galvanized deck and її equipping with electricity. Zalezhno in your name, TOV "SeverBudLis" will order you different ways installation of electrical wiring on vibr.

06/05/2015