Heating pads from water scorching. Cable for burning. Positive aspects of closed installation

At the same time, it is already obvious that the price of energy supply and nadal is increasing. To that, food came before the stingy man: how to spare your scorching on the vartos? Obviously, the construction of the booth is insulated, plastic windows solve the problem of heat loss, and more importantly, the correct installation of water scorching. When scorching your booth, you can choose one of the types of water scorching:

• radiator;
• plinth;
• warmth of the podlog.

In the private sector, in your own booth, the choice of scorching is always different, so that the installation is planned on the cob of everyday life and can be easily installed, whether it be some kind of scorching. At the ordered house, especially with the classic plans, it is already installed radiator not scorched. It is possible, obviously, to re-dominate the system, but if necessary, take it from the ZhKG, re-lay the bottom.

What is the warmth of the pidlog?

Pіdloga z pidіgrivom - tse not vіdkrittya of our century. Similar design of the system is based on Ancient Rome, where special channels were laid at the palaces, they went hotter. At our hour, a bunch of warm weather was “fashionable” to install in kitchens and bathrooms. This is explained by the sighing from the bottom, which brings the summer period to a cold one, then you can see the heat conductivity. Today, there is no room for laying the lower heating, the professionals have learned how to mount the pipes for any stately cover. And, regardless of those that the parquet is growing, linoleum is being worn out under the influx of heat, nobody is particularly worried about this drive, everyone continues to plan the installation of the lower pipe in their booths.

The most important thing for the lower pіgіrіv is that the robot is as big as the battery. The heating area of ​​such a bottom gives a superior advantage in parity with other types of heating.

Methods for installing sublogs with heating

Selection of sublogs for heating the surroundings in two ways:

1. Pipes from heat transfer fluids.
2. Electrical cable.

The main advantage of installing with an electric cable is simplicity. You can lay a cable to a depth of 1 to 3 cm, whether it be a wake-up call, or you can install an electric generator with your own hands, as you can see, even if it’s a trifle, you can use it in electricity. Tim more, installation options, be it as it may be, can be found on the video with detailed installation instructions.

The axis will only be expensive to operate an electric sub-log. The water bill is economical.

The installation of a sub-log with heating in the form of water scorching is foldable and requires an exact fit of the singing scheme. In order for your underlay to function correctly, the binding of the mind - installation of a screed on concrete or an increase in surface underlays by 7-10 cm. You can't do without professionals here, especially as it is planned to install it on the whole area of ​​the apartment. Incorrect installation of such an installation option can lead to a deplorable result: you will blow a fire near the scorching system along the entire perimeter of the booth.

To that pipe with heat transfer will already be walled up in concrete. Choose a pіdlog with pіdіgіvom better in the fallow land in the area, so you need to warm it. So, if the application, which is heated, is small beyond the scope, then it will be obvious that there will be an electrical connection. And as a matter of fact - heat the whole house, then it’s better to protect it from the water scorching. One of the minuses of the lower pipeline with heated water is the installation of a pump, the heat-carrying chips will not flow through the pipes.

Naygolovnіshі perevagi bottom z pіdіgіvom on water scorched:

• Visually invisible all scorching accessories.
• Heating from the bottom is visible along the entire perimeter, where the pipeline is installed.
• Possibility to heat great areas with small means.

Nedolіki bottom z teplosієm vіd vіd scorch water:

• Impossibility of curing by the temperature regime of scorching;
• Falling vice at the riser;
• Mozhlivist prot_kannya that difficulties її poshuk;
• Foldable installation;
• Zaboroni ZhKG

Yak vlashtovana pіdloga z pіdіgrіv

As a matter of fact, the lower water pipe has its work - the battery is walled up in the basement, the heat carrier is fed into the yak. The heat-carrier gives heat to the material of the pipes: concrete, aluminum plates, sand. Then the heat is transferred to the main cover at the bottom, from the other surface the heat rises uphill, warming the room.

The scheme of the lower pіdіgіv polagє:

• іz teploіzoljatsії, yak piping pіd trumpets, schob heat did not go down;
• polyethylene slinky;
• reinforcing meshes;
• pipeline;

• concrete screed;
• pidloge cover.

As you have some small new beginnings in everyday life, you can try to install the warmth of the bed with your own hands. It will be easier if you know the photo - instructions for installation. Obov'yazkovo when installing the lower pipe, follow the instructions:

1. A heat-insulating material is laid on the back: foam plastic, foam plastic. Zavdyaki tsim materials warmly do not go down.
2. A line is laid to compensate for the expansion of the heat of the screed.
3. Fittings are installed, pipes are fixed on the new one.
4. The pipeline is being restored. You can choose whether the form of laying: snake, mushli, ale, if you look at a photo, you will rather lay it in a spiral.
5. Three meters one meter behind the help of special clamps, the pipes are installed to the fittings.
6. It is closed in the collector, which supplies water with one set of pipes, the next to the collector.
7. After the completion of the work, the system is launched, in order to review the practicality and reveal the possibility of failure.
8. If the system functions without problems, then the installation of a concrete screed from the bottom with a height of 7 cm should be done.

When installing pidlogs, it is necessary to ensure that the linoleum, laminate screed is laid thinner, the concrete screed can be tiled. Such installation is due to different thermal conductivity of the material.

With this material, I want to discuss the scorching pipes in the pipeline: pluses and minuses of the solution, economy and comfort on the aphids of convective scorching, as well as the installation of materials and the procedure for installing water heating pipes. Otzhe, let's do it.

What is it

The main idea of ​​the scorching scheme, what to call us, is that scorching attachment to fight the whole pіdloga at the occupant. Zrozumіlo, for a wine, there is a place for roztashuvannya of large-sized stationary furniture: a pіdloga pіd vbudovanim аbо lіzhkom bіgіvat without gluz.

Heating up the pipes of scorching at the screeds. The stench is laid with a croc of 10 - 20 cm on top of the insulation and is concreted. As a final covering, there is a choice of whether there is a material with a high thermal conductivity - kahel, laminate or linoleum.

Pipes of heat underlayment can be laid without a concrete screed, on a wooden subfloor. Prote vіdpovіdnі stowage schemes I will not zachіpatim in tsіy stattі: stink merit on the okreme dolіdzhennya.

As a heat insulator under the water heat under the traditional vikoristovuetsya extruded polystyrene foam with a thickness of 20 - 50 mm. Insulation does not give heat transfer to a bedroom with a pіdval or susіdskim apartments overlap.

Gidnosti i nedolіki

Understanding, it is possible to formulate a little more like an alternative. In this role, there is an obvious convection scorching. real radiators h Vіdkritim divorce heat transfer.

Pro

• Warmth effectively secures significant heat savings. Not too big - close to 10 - 30%, ale vіdchutnu. Heating up the cold to 25-35 degrees to bring it up to the point where it warms up again on its own, where heat is necessary - without a middle over the cold and at a height not higher than human growth.
  As the temperature rises, the temperature is the same or a troch lower. For cooling - in case of convection scorching on the riverbed, it can be +18, and on the wall +30 C. With internal heating, the average temperature in the premises decreases, and therefore, the delta of temperatures outside the street;

The very difference in temperature between the middle and the call of the booth is determined by the loss of heat through the walls, under the bed and the bed, which is brought about by heating.

• Heating pads ensures unobstructed comfort. Do you remember the old saying “tremise your feet in the warmth, and your head in the cold”? The heat of the podloga allows realizing її literally. Zakrema, you can forget about stretching over the pidloga and calmly allow the child to go to the kilimka, not being afraid of colds;
• The low temperature of the heat carrier is also visible when the heat of the heat pump is higher. The greater the temperature difference between the low-potential dzherel (street winds, water or soil) and the water in the circuit, the greater the electrician's supply for the removal of a kilowatt of heat.

The effect does not depend on a specific type or model of a heat pump design features vsih without blame virobіv tsgogo.

Contra

Water heat for a private booth more expensive for convection scorching. Are you in doubt? Let's win a simple rozrahunok:

• The price of an inexpensive PERT pipe with a standard diameter of 16 mm is about 50 rubles per linear meter. Approximately 100 meters are needed for a room with an area of ​​20 m2 (when laying with a crop of 20 cm).
  The total cost for the pipe is 5,000 rubles - without fixing the concrete preparation for overlapping, reinforcement, screeds, insulation, clamps for fixing pipes and collectors with throttles;

• For por_vnyannya - heating tієї and kіmnati it is possible to provide 8 - sectional aluminum radiator vartistyu ... ta-dam ... 2400 rubles. From additional vitrates - less than 5-10 meters of reinforced polypropylene (60 rubles per meter), a few copies of fittings and a pair of truss faucets.

Dali. Water supply can be heated up to 30, maximum - 40 degrees. Tse obezzhennya correspond to the owners of thermal pumps, and the axis from the inhabitants is connected to the central scorching of the houses and apartments out of harm's way.

Їm happen to fence the folding circuit z primus circulation, tripod valve and temperature sensor for temperature adjustment. But I’ll wake up again, and chimali.

Laying pipes at the screed hot-not-hot get to know overhaul . Tse will not be a problem in the Novobudovs, but the axis in the apartments, they hesitate ... well, you understand. Then you can install batteries and build water supply and risers, without hanging out of the room: from the work of the laborers, there will be no more drilling than a few openings near the walls.

The log in the process of work will become 8 and more centimeters (insulation and screed with pipes, remember?). If you need to align the pidlogs in front, 3 - 5 cm more, take the concrete preparation (laying low-quality concrete).

The maximum thermal intensity, which can be taken from the heat inputs at a reasonable temperature regime and despite the fine coating of materials with high thermal conductivity, is about 70 watts. There, there is not enough of it (that is, at least on the whole territory of Russia, in the Urals and in the countryside), the warmth of the bed can be supplemented with convection scorching accessories.

I to the speech: I did not say that the water of the heat of the pіdlog - is it expensive to do it?

Materials

For laying in a screed, zastosovuetsya:

• metal-polymer pipe;

• Sewing polyethylene PEX (polyethylene, which in the process of chemical or industrial processing removes cross-links between molecules). Zshivannya zbіshuє thermostіykіkіst polimer and yogo mіtsnіst on rozrіv;

• Stabilization of polyethylene PERT, which is practically practical in vіdrіznyаєєєs vіd sewn only after the effect of memory (the building of the pipe will soon be short after the expansion) and in another way to the installation of the fittings.

The axis of the minimum price on them for pipes with the largest running diameter is 16 mm.

Unfortunately, I can’t unambiguously hang on to the melancholy of one type of pipes:

• On the melancholy metaloplastika say yogo great mіtsnіst razryv (working vice 10 atmospheres against 6 competing solutions). However, when the pipe is bent, the aluminum core is easily broken. Offended by seeing polyethylene, they do not suffer;
• PEX was overturned by the fates of exploitation and did not cry out from the Vlasniks of the day. Then, for do-it-yourself installation, you need a relatively expensive tool - an expander, which allows you to stretch the pipe, first pull it on the fitting fitting;
• PE-RT brewers advertise as a variety of polyethylene, especially resistant to high temperatures (which in a circuit with 30 degrees does not give any special advantages). The unparalleled advantage of the new material is its low cost and the fact that the assembler's instructions allow you to use not only mechanical, but also cheap manufactured fittings for installation.

Mounting

More than once, sing, less than a hundred times, feel it, why not?

At the same time, heat is being installed at the booth of my closest relatives. It's a pity, I'm not able to make a photo report from the US in stages; prote the main points fixing.

First off - short description that which, vlasne, sporudzhuetsya:

• Dzherelo heat - heat pump "povіtrya-voda" in the company DanHeat pressure 12 kW. The climate of Sevastopol allows you to cook yoga for heating tsiliy rik. Zovnishhnіy block of mountings on the paved bіlya booth; all other thermal conditions (including a heat accumulator tank with a volume of 300 liters) were brought down to the bottom;

In the photo - the original block of the heat pump.

• On the skin version of the double-top booth, a vlasny collector shield was selected. Vіn allows centralized curvature of the temperature regimes of the skin contour;
• Distribution of heat transfer to the shields of the vikonan reinforced with polypropylene;
• Vikoristan PE-RT pipe for connecting fancoils - accessories for cooling applications. Thermal, as it is easy to guess, while working and in the air conditioning mode.

Now about those, how the editing was done:

1. The old screed with a great number of cracks has been completely removed, so as not to increase the pressure for overlapping and not change the height of the beds;
2. Plate over the virivnyane concrete preparation with reinforcement of fiber (we chop with fiberglass);
3. On top of the laying of a plate of extruded foam polystyrene 30 mm. Laying - without fixation, the insulation will be pressed with a screed;

1. The pipe is fixed to the heat insulator with polyethylene clamps with a 20 cm crochet. Laying is marked with a "raw", which gives a greater equal distribution of temperatures in the middle of the contour. The length of the skin contour does not exceed 100 meters; Tim, it’s not enough for heating all the areas under the logs, pipe laying the dekilkom with independent contours;

Laying with a "raw" gives the most equal heating of the screed.

1. All connections are fixed behind the screed boundaries - in the collector shield and on the connection with fan coils;

1. Pipes are poured with a screed with fiber-reinforced concrete tovshchina close to 5 cm.

And now - about the bag: more than spending on heat, the possession of that pipe and heat pipes for their installation exceeded 800 thousand rubles. Let me remind you - with the maximum cheapness of the heat source: the heat pump "replacement-water" is inexpensive, both by itself and in installation.

For the improvement of all the work, connected with the glazing of the heat pads, the windshields (direct and indirect) add up, according to my rough estimate, close to 1,200,000 rubles with an opal area of ​​280 m2.

Just for reassurance: the organization of heating my house with an area of ​​150 meters with inverter air conditioners cost about ten times cheaper. With a lot of equal operating voltages on the heat supply: the inverter is the same heat pump, which is also used for the repeat-repeat scheme.

Visnovok

Shanovni chitachi, do you check for any remaining vysnovki? You won't. My task was to give you a thought before thinking, and, I agree, I'm vikonav.

As a rule, a bit of additional materials can be found in the video in this article. I check your additional comments. Good luck, comrade!

March 31, 2016

If you want to say something, add clarifications, ask the author - add a comment and say thank you!

For the sake of justice, let us designate that we have completely heated the booth under the force not only of the radiators. Warm podlogs cope with the task not harder. In Ukraine, this way of heating is still not wide enough. I Main reason crying over the financial possibilities of spivvitchizniks, and to destroy the stereotypes formed by the protracted decade. Believe in those that houses can be heated without traditional batteries, buildings are still not all. And the darma, even the warmth of a podloga, is today that energy-efficient alternative, the advantages of which have long been known from Europe. Zokrema, in Norway, in the fatherland, warm weather, climate fires have up to 80% of life.

So why have these systems outperformed? The principle of robotic centralized scorching of the offensive: the heat from the radiators rises to the wall, and the colder it falls to the floor. As long as the lower balls heat up, the upper ones reach (and part of the heat is still provided by ventilation). Let's repeat the process. Convection currents create a super-friendly atmosphere, which gives orders "Try your feet in the warmth, and your head in the cold" exactly to the point. As a result, regular stretching on the equal footing caused discomfort and not transferring energy to the heating. When scorched by the system " warm weather» It only seems to collapse in one straight line - from the bottom uphill. The “heating” area is large for the safe and even heating of the air in the premises. Until then, it’s warmer again, you’ll always be known below, crim protyagiv. With a heating system, the energy consumption drops by approximately 20%. And the system warm weather"absolutely invisible, it does not affect the design of the application, and may be a great warranty term, which indicates the quality and durability.

On this day, there are two types of heat supply: water and electricity. Independently, the system includes heating cables (circuit), a thermostat with a temperature sensor, thermal insulation and fastening. The stench is mounted the same way - at the screed pіdlogi. Ale є y vіdminnostі.

The heat water is a prerequisite for the additional purchase of a boiler, which increases the variability of the installation of the system. Ale, yakscho vrahuvati, scho ekonomіchnіshі vikoristannya, the residual amount is equal to the varnostі elektrichnyh models. The zamіskom budіvnіstvі vodіnі sistemy muyut impeccable prevaga, even the problem of energy efficiency nabuvaє urgency on its own great squares. And in the summer season, the stench helps to cool down the application for the help of cold water.

Electric heat supply is easy to install, does not require additional equipment and preventive maintenance during the period of operation. Ale vikoristannya electrical systems less vigіdne z look economy. To that, ring out for them to install a booth in the next room (at the front, bathrooms or kitchens).

To the Ukrainian market of the system sublogic scorching We supply a lot of companies, including Aquatherm, Rehau (Nimechchina), Ceilhit (Spain), Devi (Denmark), Easy Heat (Canada), Ensto (Finland), Fenix ​​(Czech Republic), KAN (Poland), Nexans (Norway) , ThermoTech, Wirsbo (Sweden), "Our comfort", "Teplolux" (Russia), NVP "Eleter" (Ukraine) and others.

Like a pіdlogu pіdlogu, so vіn i serve

Installation of the system warm weather»With special training, this is achieved by qualified workers. But knowing the basic principles of that underwater stone laying will help you to control the process and to correct the non-acidic work.

The system is laid on a black base before pouring the screed. There are two types of pipe laying: parallel (snake, snaky) and spiral. Parallel stowage is suitable for small spaces, as well as a pidlog with a trick. At the same time, the hottest pipe (the place where the heat-carrying one is located near the snake) is roztashovuetsya in the coldest zone, for example, at old wall. Spiral laying is more suitable for large rooms, as well as for the city, where the temperature difference is negligible. The most cold-hearted maid trumpets to judge from the coldest, so the temperature is constant throughout the whole area.

The electric heating cable is laid only on the surface, in the form of stationary furniture and underground by-button technology and water pipes can be laid over all areas (they do not threaten overheating under important objects). At the places of installation of heat pipes, it is not guilty of buti pipelines that electrical cables. Vіdstan vіd mіzhі vіgіvаєєtsya ploschі primіshchennya up to the heating cable аbо pipes аrіvnіuє half kroku laying (vіdstanі mіzh coils contour). And in the areas near the old walls of life - the so-called border zones - the laying of the bagzhano is changed to compensate for the waste of heat.

Under the hour of laying the thermal circuit and pouring the screed, just fill it, so that the robots did not vitiate the system. It will be possible to reconsider її pratsezdatnіst only after repeated hanging of the screed (after 3-4 tizhnі), and as the system is damaged, it will be possible to open the sub-log and mount it again.

One more factor is added to the moisture content of the water heat and the water is the quality of the water in them. At the first filling of the pipes, run after them, so that the workers would really wash them, and then they started heating the water with the addition of a 1-2% reagent.

The systems installed after the start of the service could not be repaired and maintained under the longest term of service. The truth is, there are still a few factors that add to the accuracy, and more smut, to the efficiency of warm conditions:

• the pressure of the circulation pump was correctly adjusted (in case of insufficient pressure, the coil found in the contour of the matima is insufficient pressure of the water);
• basic regulation rozpodіlnogo collector(as it is not vikonana, water circulates less in short circuits, de opir is smaller);
• vіdregulirovaniya vuzol zmіshuvannya to the set temperature (in this case, the temperature of the warm weather will be uncomfortable).

Must and nuances should be discussed with specialists at the hour of the installation of the system. Tim, you yourself will secure yourself from unacceptable surprises in the future.

Thermoregulators for heat supply

The thermostat is a single element of the heating system, visible in the interior. The main task of the thermostat is to trim the set temperature.

Only on the view of the thermostats of the radiator, the object of this respect is the temperature of the logs. It helps to avoid the situation, if again in the room (for example, in the bathroom or in the kitchen) it warms up even hot, and the bed is cold. In addition, there are more functional thermostats, like two sensors can be used - repeat and logs. As a rule, such models are vicorous in systems that are not only used for heating up the logs, but also for heating the entire application (due to the availability of other heat sources).

When choosing a thermostat for heating, remember that this tension, that it is connected, is due to the tension of the heating system itself. According to current standards, the maximum pressure of thermostats is 3 kW (approx. pralna machine). Due to the tightness of the installed system, it is necessary to additionally switch the power relay or set the thermostats.

Installation, adjustment and prophylaxis

Radiator thermostats are suitable for any kind of home heating system. This installation is clumsy and does not require special qualifications special recognition). Finish reading the instructions enclosed in the package. And yet you have never had a chance to win such robots on your own, rather turn around for help to fahivtsya. Whether a slyusar plumber can install a thermostat without any problems, or you can do it right up to these instructions.

Wu vipadu z with warm words The installation of the thermostat must be given special consideration. Attachment is placed on the wall (otherwise it will be in it - fallow in sight) in any handy place, but not more than lower on the wall 30 cm in the view of the logs. Open the back in the wall and close the door for the installation of a thermostat. Before yogo installation, bring food. І less then we will install warm weather. The reliability of heating systems for 99% depends on the quality of the installation work, so it is better to trust the robot to specialists (and the installation of temperature controllers, among others).

Adjustment of the temperature controller for warm weather is not more than 20 minutes. The set parameters are saved in the installation memory and are recalled after a power failure - to be notified about the thermostat battery power supply failure. Krіm programming settings, use and additional buttons for cleaning, which allow you to change the temperature or the mode for the next hour. As soon as you press the "Confirm settings" button, all parameters are rotated until the hour and temperature are set.

We don’t live in Africa, but in some other country with a sweltering climate, all kindly understand that after heating up the butovyh, office and other common places, they will be deprived of actual food at the objects that will be. The main place for a be-like a person who would like to rest in an atmosphere of comfort is that calm, obviously, it’s a donkey.

There, a person grows up, speaks out of his own family, he himself will make a majestic injection and on those, like a person who works.

Alternative scorching

In order to achieve maximum comfort in the premises and at the same time save on the payment for the scorching of the plant, the people were able to develop the awareness of the scorching and new and new forms. Today, it is no longer a role of both the main and additional alternative scorching.

The scorched podlog was found to be even more efficient and ergonomic method. The principle of robotics of the system polagaє at the building of warm weather rises uphill. Coldly, turning your blackness down, and, warming up on the surface, rise again.

There are three main advantages over classic wall-mounted radiators:

1. Rivnomіrne razpodіlennya heat flow on vsіy surfіnі pіdlogі vіdpovіdno іn primіshchenniu. Classically scorched with radiators fixed on the walls, often flooded with cold weather.
2. Povna bezpeka, through the presence of direct physical contact with baked surfaces.
3. The idea was to combine communication under the eagle, giving great new opportunities for design inputs in the perfect interior space.

Note!
It is less important to lie one factor - the installation of that connection Opal system pid pіdlogim pokrittami It is better to trust professionals, as they give a guarantee for all types of services.

scorching systems

The most demanded today are two heating systems:

• Electric.
• Vodyane.

This and the other type of alternative scorching may have its own advantages and shortcomings, as well as recommendations for stagnation in fallow land due to their main character.

Electrical heat supply

The system of electric burning, which is easy to install, is the most accessible for any kind of laborious work of all robots with their own hands. Tim more, what should be included in the sets of warm pads report instruction from the installation and adjustment of the system.

At this moment, the first wave of economy is planned - you will pay less for the necessary benefits. In addition, it is similar to the scorching in the apartment, it is significant to change the volume and height of the space, so that the entire technological ball is borrowed literally 3-5 cm at a time with a cement screed, which is curved.

The electrical state of the scorched can be two different:

• Cable (maє vomogi until I become the foundation - smoothness).
• Plivkove pokrittya can be laid on an unprepared base that does not require additional stains for the repair of the underlay.

Pratsyuє i that i іnshiy type elektroobіgrіv pіdlogi for rahunok nagіvannya main element elektroenergiєє, scho podlaє. Thermal energy from heating cables or thermofusions is transferred until the cover is thin.

Respect!
Mayuchi in his order heating elements on the surface, whether it be cables, smelting or pipes of water scorching, warto remember about the zones of neobov'yazkovy, and sometimes non-baggage heating.
Up to such places you can see the surface under the refrigerator, furniture, built-in large-sized equipment.

water scorch

This method of scorching the pipes is controlled by the pipes:

• In a spiral.

• Looks like a snake.

In the role of heat transfer in a similar system of scorching, hot water circulates behind the pipe system.

The heat conduit is connected to the heat transfer station:

• Gas cauldron.
• Electric heater.
• Cauldron on solid fire.

Water circulation at the system is secured with the help of a special pump.

Such a number of achievements:

• Hopefulness.
• Durability. With the appearance of polymer pipes, the term for the service of the water system of scorching is different.
• Cheap exploitation.

Before the shortfalls, you can see:

• Compliance with installation. As we have already said, it’s a good idea to ask for a fahіvtsya.
• It is a remarkable technological community to rob the scorching ball with an important and undersized stosuvannya in apartments with a standard low height of the beds.
• Takozh water system the heat of the log is important to regulate.

Incineration systems

One of the oldest ways to heat the place is to rediscover it. Today, similar systems of scorching stagnate in large, virobniches and other premises. Ring out central scorching, confusion from heat-exchange tidal ventilation.

Vіdomi takozh vipadki vykoristannya povitrya living booths. Mіstseve povitryane scorched pіdlogi zdіysnyuєsya heat up. in a different way(with heaters, thermal harmats) I will repeat, as if for the help of a fan, it is taken from the premises and after heating it turns to a new one.

Visnovok

You didn’t choose any kind of scorching, you need to remember about the dotality of vikoristannya tiєї chi іnshої system at your booth. If it’s cold to come into the apartment on a cold day, then the heat of the cold, obviously, heats up the room, but spend heat, then, and increase the electricity. In the video presented in this article, you will find additional information on this topic.