Connecting a vbudovanoy hood. What do you need to know about the time of connection of the ventilation shaft to the ventilation shaft? The nuances of installing a kitchen hood

Installing a stained glass hood in the kitchen is not a bug, but a necessity. Good ventilation is to continue the term of service of kitchen furniture, avoiding the appearance of boiling and soot on the walls, steles, cornices and curtains, but more importantly - a drawstring helps to clean the air from the shkidlivih for people's houses. Various products of combustion, carcinogens and vaporization are seen under the hour of the cooking process, which cannot be done without the introduction of a draw. Moreover, it is necessary to choose a drawstring and the installation time is well thought out.

It is not a problem to buy a drawstring in the store at once, and to install it independently, it is also a whole lot of strength and newcomers in repair robots, and even more so to an experienced maestro at all costs. Information about how to install kitchen hoods, as well as knowledge about sanitary standards and safety rules, will significantly simplify the installation of this kitchen equipment.

The principle of robotic pull-in outbuildings and see them

Razrіznyayut kіlka vidіv vyazhok according to the principle of work:

1. Classical vityazhnі pristroi vydalyaet zarudnennoe poіtrya іz vіshchennya through the ventilаіy duct.
2. Recirculation drawstrings are soaked again, passed through the filter and turned back.
3. Combination type of drawstring can be used as a drawstring, and in a filtering mode.

For the installation method of kitchen hoods, refer to:

• The stench is in the kitchen furniture that is above the stove.
• Pіdvіsnі - hovering under the wardrobe over the stove
• Nastіnі - fasten without a middle to the wall
• Islands - fasten in the middle of the kitchens to the stele.
• Kutovі - fasten at the kutka

Draw-in rules

Be it a kitchen drawer, it is necessary to mount it according to the adopted norms and rules, so as to ensure a safe and stable robot fit. It is especially important to choose the height of the installation of the draft above the gas or electric cooking surface (or above the stove). For an electric surface, it is 70-80 cm, for a gas one - 80-85 cm. It is also possible to cause a pozhezhu, which is unacceptable. If you put the drawstring too high, the efficiency of the work will decrease.
It is also necessary to correctly select the width of the drawstring. The width of the cooking surfaces and slabs is standard and more expensive 50-60 cm.

Depending on the type and tightness of the kitchen hood

Select type kitchen hood deposit due to rich factors: due to the place of roztashuvannya ventilation duct that vіdstanі up to new, vіd kitchen furniture, the type of stove is too thin. It is necessary to secure the diameter of the adapter between the opening at the ventilation duct. It is important that the larger diameter of the diameter, the smaller the tightness, you can use an attachment.

The power supply of tightness of the drawstring - on the right is completely individual, but don’t forget to buy the tightest accessory is true. Pick up the windshield according to the diameter of the ventilation duct, and if you take a too tight attachment, then the electric power will be richer, and the KKD will be low. Great obyag povitrya, scho get involved tight drawstring, all the same, do not go through the narrow ventilation duct. As practice shows, the best performance is achieved with small and medium fan speeds.

Connection of recirculation drawers

Another type of stained-glass windows is used in the filtration mode, such attachments do not show a repetition of the premises, and therefore there is no need to connect them to the ventilation shaft. The efficiency of everything should be based on robots and filters, that is why they are to be changed in the meaning of the term (not more appropriate, more often than not).
The installation of this accessory is simple: you only need to fasten the drawstring on the wall and connect it to electricity. When repairing the kitchen, the next step is to designate a place for roztashuvannya vents and to carry out electrical wiring to the location of the socket to the next place.
To mount the drawstring on the wall space, apply a rosette, drill with a perforator or drill the opening on the wall, so that the fastening of the drawstring comes up, screw dowels into them or self-tapping screws and hang attachments.

Connecting a ventilated outbuilding

Drawstrings, which are removed again from the premises, must be connected to the ventilation duct. In case of need, it is necessary to insure vіdstan vіd roztashuvannya of the draft itself to the ventilation shaft. Too long windings do not look aesthetically pleasing and reduce the effectiveness of the drawstring. Because the slab of that stained glass above it is far from the ventilation shaft, but close to the window, it is an option to add an air-conditioning to the channel to a specially designed opening in the main wall.

The process of connecting the ventilation hood to the ventilation does not require folding, and even for the connection, there are special windings and adapters for the connection. It is not necessary to hermetically put all the elements between each other. Ale є deyakі rules, dotrimannya of which guarantees the normal operation of ventilation in the kitchen:

• The connection of the pipe to the draft is not to blame, it is not the fault of the ventilation duct, the shards, if the draft is not working, it is the fault of the natural ventilation for additional draft through the additional grate.
• For the normal operation of the winding, it is necessary to ensure a winding, which will be drawn without interruption of the winding flow.
• Dovzhina povіtrovodu that kіlkіst yogo povorotіv may be minimal.
• It is best to beat the pipes with smooth walls. Corrugated pipelines can be bent under different cuts, but the surface is ribbed on the surface.
• Turn the turnpike next to work not steep, but smooth.
• For the normal operation of the draft, an influx of fresh air is needed, so it is necessary to ensure the ventilation of the premises, or a constant intake of air from the streets.
• If there is a geyser in the kitchen for heating water, then the drawer at the same time cannot be installed in the chimney channel of the column.

Like Bachimo, the installation of a ventilation hood and a connection to the ventilation duct is not foldable, but at the same time it is accompanied by singing nuances, adding some of them to help build a normal ventilation system into a booth.

Rockiv so twenty-thirty years ago the stele was salted and the high water content in the kitchen is the main concomitant inacceptability when cooking hedgehogs.

Don't say a word about the smell, even if it's often vin buv priemnym and sponkav until podnyattya appetite. Schopravda, which is the vineyard of the river.

In those distant hours, such problems were simply raised:

• The surface of the stele has become salted - it is necessary to repair (pobilimo);
• It became strongly hairy - I could see the apartment (trochs are cold, well, it’s tolerable);
• The smell of fat does not fit, so we go out into the street and walk.

AT modern minds the people began to chirp to the point of zruchnosti that comfort. That economy of the family budget comes to the fore.

Identity shoroku robiti repairs - do not waste pennies every day. Until then, no one should beat anyone in the kitchen.

That’s why it’s only one way, to avoid all the other inaccuracies, it’s necessary to install a modern hood.

It is especially significant that the brewers promote two main models:

1. Іz closed loop.
2. From the system of entry for inter-rooms (photo above).

The first model may be less short and it is less likely to be connected in quiet weather, if it is not possible to connect an attachment to the ventilation system of the booth. To that food, how to connect a drawer to the kitchen, today it is relevant.

The nuances of installing a kitchen hood

Another model is the most effective and the most optimal option. Ale, as practice shows, to instill in someone, it would be given to a clumsy process, its own stone water.

• First, ease of installation only works. Zvichayno, you can win the forgiveness option and bring a drawstring for an additional trumpet-corrugation. Ale tse for the quiet, who does not think about the aesthetics of the book. Let's add here and such an unacceptable moment - corrugation for an hour of robotic cleaning and noise again.
• In another way, just take that switch and the purifier may turn out to be insufficient. Sometimes it is carried out in such a way that it is necessary to make changes to the design of the box. Here you need the deaki novice robots with tools. Tsі zm_ni nebhіdnі at razі, yakscho traction vіdpovіdaє nebhіdnim norms. In principle, the attachment itself is responsible for ensuring the ventilation in the kitchen without the help of a regular fan. Ale is so traplyayetsya (ventilation clogged) that the fan can not cope with the air intake. Often, the fact that the ventilator is installed with its own hands creates such problems in the process of exploitation, at an hour, if it didn’t start, the masters are given paradise.
• Cone mounting. The simplest process, in which case it will be necessary to protect a small amount of indicators and parameters. The height of the beds, the total accommodation, the intensity of the ventilation. Here it is important to accurately push the cone to the ventilation opening.
• Connection to electricity supply. The best option is to clean it again by plugging it in to the socket, so that you can do without plugging it into the outlet.

Like a bachite, the connection of a drawstring in the kitchen is not easy on the right and it is serious to do it. Therefore, it is a sense to shift the vantage of vіdpovіdalnostі to fahivtsіv (div. also article).

The truth is, the price of the whole process will increase, but the safety and efficiency of the robot will be more expensive.

Respect! Vіdstan vіd vіd vіdnі vіdnі varilnoї stojі until ochishchuvach poіtrya is called the lower boundary. Tsey showing for gas stoves guilty of adding 75 centimeters, and for electric stoves 65 centimeters.

In that case, as the design project has overhauled the border, it is necessary to buy a drawstring greater area filtration.

There is no sense for the one that has a larger size, it will cost more dearly, but in a different way, the effectiveness of this will be less. That's why we're going to have to go flat, so that the designer has vrahuvav tsi parameters.

Everything, the same, is brought to the furniture, even more often, to attach a winding pipe, to lay a cristally hanging closet. To that, in the new, open the door open.

In order not to be tormented by the problem itself, it is necessary to take care of the house when buying furniture, so that everything was destroyed at the workshop. Ale, if you are guilty, tell the roztashuvannya open.

See the drawer for the installation method

Іsnuє p'yat vid_v ochishchuvachіv vіtrya, the installation of such viznaє surface, on the way the stench will be creeping.

1. Suspended drawstrings. Їx sound to install over the stove under the hanging closet.
2. Vbudovani. The space of the roztashuvannya in the middle of the hanging shafka. It’s easy, it’s not visible, but the connection of the hood for the kitchen takes time and patience, because the fastening in the middle of the wardrobe is not transferred. Here it is necessary to accurately set the shafa itself, and the drawstring, not only for equal, but also for height. Fastening is carried out either with self-tapping screws, or with special bolted fasteners.
3. Real cleansing wipes. Everything is simple here, they are installed to the wall and fastened with special screws or dowels.
4. Kutov. Let's see everything here.
5. Islands. Їх move to the stele, vicorist all the strengths and fastenings, yak go at the set with the attachment. The strength of the reinforcement is wound up to the insole surface.

How to connect a vbudovanu vityazh

• For whom in Persh Cherga happen to be drilled in the furniture, open the air duct (corrugated hose or PVC flat channel).
• After that, the cloak behind the bowl is restored to the required height. The cleaner will be shown in the closet, and the windshield will be inserted into the opening. Mіzh themselves stinks with a special collar, which is not included in the kit, that one should buy it for a long time.
• The diameter of the clamp may be consistent with the diameter of the appropriate elements. It should be respected that the space of the windpipe and the transitional flange of the drawstring of the obov'yazkovo should be smeared with sealant, for the sealing of hermetic seals.

How to connect the current option

It is practical here, the same, only without furniture. The closing of the elements is carried out after the additional collar and sealant. And the axis of the drawstring itself needs to be attached to the wall.

Open the chimney on the attachment, apply the back of it to the wall exactly at the required height, and open the badges open.

Let’s open the door after the instructions, where dowels and screws are inserted (instructions for installation are included in the kit).

Vityazhka hangs itself on them. Naygolovnіshe - to be brought to the wall and povitroprovid. Ring one collar enough.

For a big gift to their families, the kitchen is the queen of the apartment and the house. Itself there you get ready for the most delicious, calmly play the teapot and stand a unique aroma. Ale, sometimes the aroma is not only in the kitchen, ale and in the reshti of all the rooms - which is already unacceptable. Not kazhuchi already about the smell of burnt herbs. Vіd tsgogo vryatuvati only yakіsna vytyazhka. If the decision about the purchase has already been made, then it is not necessary to go to the store for a new thing. Rather, the system should be vichity all proponated models and how to connect a drawstring in the kitchen.

Tipi drawstring and short description

Kitchen hoods are of the following types:

• Really. Mayuzhe raznomanіtny design of the body, so everything will be fine with the aesthetics of the kitchen. It is mounted without a middle over the stove to the wall;
• Kutov. An ideal option for small kitchens, since a centimeter can be more functional. Fixed on the wall at the kutku;
• Pіdvіsnі (flat). Perebuvayut without a hitch over the stove, under the wardrobe;
• Vbudovani. Mounted directly into the closet itself;
• Islands. The most universal type of kitchen hood. Є mozhliv_st montuvati practical whether de kitchen primіschennya. As a rule, for large rooms, de kitchen furniture should be placed in the middle.

If, you know, the kitchen drawer has been bought, it is necessary to take care of the safety of your work. The first step is to independently connect the drawstring, it is necessary to ground it. If the houses are new and repaired recently, then there are Euro-type sockets near the walls. The grounding terminal has already been transferred there, it is only necessary to come to it. Like old sockets, you can independently ground them by attaching the wire to the metal on the case.

In principle, nutrition, like plugging a drawer in the kitchen, is often asked to do it often, so on special sites to do it a lot of different thematic blogs, video-instructions of good masters and just verbal report descriptions on the qiu topic. Enough of the most impassioned discussion about the functioning vented outbuilding, so that you can successfully install it.

Ventilation supply

Under the hour of everyday life, whether it is a special place for living, the obov'yazkovo is transferred to regular ventilation. At the time of installation of the kitchen hood, it will be broken in some way. І schob to reduce to a minimum the steps of the collapse of the fahivtsi, it is recommended to install an additional box with a valve. The vin is regulated by the help of a small spring, to which the lid is attached, from the lightest possible material. You can also use plastic or aluminum sheet.

The principle of yoga robots is simple: if the drawer is closed, the valve closes with a lid and again it is necessary to go out for additional natural ventilation. If it is necessary to remove an unacceptable smell, then the valve opens and closes, through which natural ventilation is provided. Vityaguє odors are less than a vityazh. The main advantage of this ventilation system is the presence of air draft.

Have recently awakened bagatopoverkhovy booths at the bathrooms and kitchen rooms there are special ventilation air ducts, to which, for the help of a special shield, a ventilator is connected.

In the "old" budinkas, everything is richly folded. The ventilation system is not covered by the installation of additional hanging outbuildings. And you can walk in such a way that smells, that you pass away, from one apartment you can drink in the court. And here it is necessary to take care of the Fahivets. Vіn pіdkazhe, what kind of tightness is needed a model of a drawstring. It is also possible to install an individual ventilation system, so that you can drill your special ventilation system into the street, for a 100% guarantee of protection from unacceptable odors.

Stages of connecting a kitchen hood

The first step is to connect the kitchen hood, furniture or sets are already guilty in their own places. So it will be wiser, where to connect the drawstring. She is guilty of rotting without intermediary over the stove and in the same time is not guilty of being smaller for the expansion of the stove. Roztashovuvat vytyazhka need not be lower than 60 cm from the plate. It's written in the instructions. All safety equipment. Upper threshold as soon as possible to install walkers in the kitchen, so that you can cook as comfortably as possible.

As it was taken firmly, the decision to turn on the drawer yourself, does not mean that everything will be broken to conscience.

To effectively connect a kitchen hood with your own hands, you need to fix one nuance for an hour of installation ventilation pipes: the less virgins, the more cravings will be improved.

Installation of a flat kitchen hood

I will build a flat kitchen type that allows you to connect a drawer, as there is no ventilation duct. It's easy to mount that shvidko. On this extension, it’s already a long time before the transfer of special fastenings for installation. Є 2 ways to install a flat drawer:

• For help P-like frames. For additional screws, the frame is fastened directly to the wall and serve as a fixer for the hull of the hanging building;
• Samonarіzi-studs, sometimes they are called plumbing. From one side, the stench looks like a standard self-tapping screw. On the other side, there is a thread, until a metal nut is screwed on. The dowels are driven into the wall, the body of the drawstring is fixed with a nut on the required wall.

It’s good to fix the flat hood and reconsider its practicality by plugging it into the socket. As if everything is normal, a decorative cover is worn. This model works in the recirculation mode, it is cleaned again after the help of a fresh filter. It is necessary not to forget to change the filter at least 2 times per river.

Varto can tell about the installation of the corrugations. It is richly beautiful and richly functional for a wind pipe. Do not happen to buy a happy column and adapters, the installation is lighter and cheaper. At the same time, the stores sell more aesthetically pleasing old look outbuildings. When installing the corrugation, it is necessary to expand it as much as possible, without changing the sound noise during the operation of the ventilation unit.

The winder needs to be cleaned at least 2 times per river. Wine is clogged with gar, accumulated accumulations cause a free exit of repeated flows and can become the cause of a fire.

As a rule, all current models of kitchen hoods can trifilar darts, to that the socket, in the yak will fit in, is guilty of a similar one. It is best to prepare the cream before installing the hood a new socket. Vaughn is not guilty of rotting in uninterrupted proximity to the stove itself or the mittya. That's the best, as if the socket will be above the hanging wardrobes, the trochs are placed in the center of the drawstring. Ale, at the same time z cym, її can be well seen, you can decorate with a special box.

Taking on the self-installation of a kitchen hood, we will not hesitate to ask for practical purposes from a specialist and ask for a helper, which may be necessary to confirm the installation of similar outbuildings. To find the smallest defect during installation: they screwed up the troch crookedly, filthy sealed the slots and sticks, chose insufficiently valuable and slick working material, and so on, the building will be known for the efficiency of the robotic installation or, even worse, lead to breakage.

With connections to ventilation and without heating in the kitchen, it is not only the role of removing steam and aromas from the method of environmental safety. The stinkers and pereskodzhayut psuvannu on top. Varieties of vipari, products of combustion and surpluses of fat accumulate step by step on the walls, working surfaces, and steles and undersides. After such an influx, the stench begins to fade, psuvatisya in the fatty and other deposits. For several years, the process can be reduced to a minimum in order to protect your finances and continue the term of service of kitchen equipment.

Tipi flowing drawstrings

Models and different types of outbuildings vary according to dimensions, design, price, and the principle of operation. Kitchen hoods with connections to ventilation are vicorated for maximum visibility from the space above the working kitchen surface and further deactivation of ventilation through ventilation.

The examined aggregates are divided into two types:

1. Passive models. The design does not include the installation of an electric motor. The whole working process is driven by drafts of the ventilation duct system.
2. Active kitchen hoods with connections to ventilation function to supplement the connection of electric motors, locating the middle of the dome. The motors take care of the sweating sweat that suffocates with boiling water, soot, droplets of fat.

cladding

Any type of flow-through vented structure is mounted directly above the stove. With ventilation wells, the unit is driven by special windings. Tse mozhe buti blyashany box or metal corrugation. In order to get rid of unimportant noises, equip the pipelines with soundproofing material. Aesthetic looking stench does not zіpsuyut, as if to disguise attachments behind hanging stelae.

On the neck of the main outbuilding, wind pipes are fixed behind additional clamps. The cream of the examined elements, the hoods include the following accessories:

• Coarse filter. Vіn zabezpechuє zahist of the annex itself in the presence of fat and soot.
• Fine filter. Serve the smell away. It is folded, as a rule, from the coal elements.

Timely replacement and cleaning of filters will allow not only to improve the efficiency of the work of the drawer, but to continue the term of service to the unit.

Drawstring without windpipe

Such an attachment is practically recirculating and does not require connection to ventilation ducts. After the help of the ventilator, it closes at the filtering unit, de-cleansing from odors, garou, moisture and grease. Efficiency of the robotic equipment is to lie down in the light of pressure and the filtering system. Kitchen hoods without connection to ventilation are equipped with two main blocks that are filtered.

The first system is to serve for the liquidation of fat in the face, as well as for a rough cleansing. Qi elements are made from aluminum or acrylic. The first option is effective;

A system is coming to fight against unacceptable odors, overworld waters, and excesses of the mountain. The main element is to maintain regular replacements (approximately once per quarter).

Types of kitchen hoods without connection to ventilation

All the attachments that are looked at, work on single principle, but they depend on the type of installation, but on their own:

1. A classic option for a seemingly flat parasol. There are no special design tricks. Having recommended himself a yak garna vityazhka for small kitchens.
2. Mobile models. It is installed above the stove, allowing the flow to pass through from the frontal part, which gives the possibility to creep on it.
3. Budovaya version. Allows you to hide the additions to the middle of the furniture. The pristry is reminiscent of compactness and high signs of tightness.
4. Kitchen hoods without connection to ventilation with telescopic features. Dani raznovidi can hang closer to work surface for consumption.

The aggregates are looked at differently functionally, fallow, depending on whether the stench is mounted (in the middle, in the kutka or in the water-reinforced way).

Advantages and nedolіki vytyazhok without povіtrovodіv

The kitchen, whether it be another technique, has its minuses and pluses. Vityazny annex without connection to the ventilation system may have a number of advantages:

• Elementary installation that does not require any additional fittings and suitable sleeves. Installing attachments yourself is not important.
• Economy. Vrahovyuchi, scho build kitchen hoods (60) from the connection to the ventilation vikoristovuyut an order of magnitude more energy, tsyu modification can be called economically viable.
• The variability of this design is lower, lower than a similar system with a wind duct.

The disadvantage of such units is the need for regular replacement of filter elements. Tse happen to be robiti not rіdshe, nіzh once a quarter. Kitchen hoods without connection to ventilation, the prices of which start at 5 thousand carbs, become the best helper in your kitchen.

How to connect a winder without a wind pipe?

Attachments, which are used in the recirculation mode, are easier to install, lower kitchen hoods from the connection to the ventilation. For this reason, they stink together with the ventilation shaft. At tsikh pristosuvannyah smut - min elementi that are regularly filtered.

Beforehand, it is necessary to worry about those who entrusted the electric power to the city. Before installation of the unit, mark the fixing point, drill open, install dowels or screws for further fixation of the extension. The next stage is the fastening of the drawstring on the wall, connecting it to the outlet and testing it.

Installation of the unit with a wind pipe

Behind the great rahunka, connecting a kitchen hood to ventilation does not cause any particular problems. Golovne, that the seals were hermetically and reliably fixed. For the sake of the work, follow these recommendations:

• It is not my fault to connect the ventilation channel, so that when the extension is turned on, the natural draft of the wind was blown.
• It is normal for the robot to ensure the passage of the reverse flow without additional transitions.
• The length of the windpipe and the number of curls may be reduced to a minimum.
• Vibirayuchi between the corrugated and smooth surface of the pipes, next to protect, that the first option is good to bend, but to block the flow.
• On the vines, the mother is to blame for the smooth transition.
• An additional tide after airing or a constant supply from the street to build an effective draft.
• It was fenced in to mount attachments from the exit at the dimovial channel of the gas column.

A way to connect a drawstring to ventilation on your own, not to create special folds, for the mind to trim the singing nuances and technological thinness.

Visnovok

Having taken into account the special features of the building, the principle of design, the nuances of operation and installation, it is possible to create an unusual visnovka, which the wicker can always be present in the kitchen. The choice of modification to deposit depends on the expansion of the premises, the intensity of the working process, the financial capacity and the power of the business.

Connecting ventilation hoods to ventilation, the principle of operation of foundations on the smoky air flow with distant transportation to ventilation shafts, more folding and require singling rozrahunkiv. For example, supra-worldly for the time being, the conductors will look unaesthetic and change the efficiency of the work of the building itself. When dotrimanny sing moments in the installation work, it is even easier to understand.

The option without a wind pipe in the installation is rather simple, and the price is lower. However, there are some peculiarities here. Regular replacement of filtering elements is necessary, otherwise the effectiveness of the drawer will be significantly reduced. Outbuildings without mutual ventilation may have a sprinkling of types of reinforcement, which allows you to choose any of them, be it any expansion and interior accommodation.

Connecting a hood in the kitchen to ventilation does not require special knowledge. Be it a home master as a whole, you can vikonate the operation on your own, having learned all the nuances.

Varieties of winding installations - what do you know?

When preparing food in the kitchen, it is necessary to ensure the constant recirculation of the air in the host. A couple of types of cooking stoves, aromas of burnt fire, stains at the windows bring few joys to the bagmen. To protect the kitchen from particles of fat that settle on the walls and steles, fires and boilers, it is enough to install them in it garnu draw. Such a unit in our days is an obov'yazkovym attribute of a place near a booth and an apartment, where it is prepared.

Drawstrings are subdivided into sprat types. Іsnuyut flowing, circulating and combinating units. The first ones allow the most productive and efficient ventilation of the air from the kitchen through the ventilation shaft. The flowing drawstrings are the most popular among the vacancies.

At the circulation outbuildings of the purification of the fermented wind, go for the help of coal filters. The stench is vbudovani at the case of the hood. Such devices do not need to be connected to ventilation. Їхній installation to be carried out quickly. Ale cleansing potential of circulating aggregates is the best. Combination accessories function both autonomously (it is not necessary to come to the ventilation duct), and standard ventilation mode.

Let's look at how to connect a drawstring to ventilation. Ale, it is significant that the order of installation is good for cleansing and washing in the kitchen to lie down in the same type. Z tsієї points of the gap of the drawstring are subdivided into:

• Vbudovani. Їх hovayut at the stіl or hung a wardrobe.
• Pіdvіsnі (standard, flat). Cling to the shafu, as if standing over the cooking surface.
• Kutov. Mounted at the hut of the place.
• Really. Placed on the wall right above the stove.
• Islands. Attach to the insole surface. Designed for island cuisines.

Important! can be seen on the level of 0.6–0.9 m.

Connecting the device to the electric line - be careful!

Drawstrings are used in the form of electrics, so that they can be robbed with potentially unsafe attachments. If you don’t want to take a blow with a strum, then competently bring the pulling unit to by-butovy electric lines. At this stage, you should become familiar with the main standards of electrical safety. They describe the rules for connecting by-button technology.

Drawstrings in the kitchen in the apartment or in a private booth, plug in the electric circuit with three wires - zero, earth, phase. Operate the installation without grounding!

In vents, if the living space can have a grounding circuit and euro-sockets in its own arrangement, it is not necessary to fold the connection to the ventilation unit. Everything is simple here. It is not necessary to bring a yellow wire (with a supplementary green light) wiring to the ground terminal. Nuance! Some of the drawstrings do not have a suitable rose for a grounding dart. It is not easy to get out of such a situation. It is necessary to screw with your own hands the fitting of the grounding wire and the connection with the circuit.

Now we are wondering how to connect a hood in the kitchen to the electric meter, as if the dwelling is not equipped with sockets. Deyakі clever people throw zero wire scorched radiators, pipe the water supply. Tsgogo robiti is categorically impossible. You will inflict on the safety and your life, and the health of all the people who live near the apartment house. You need to connect a zero cable to the so-called dead neutral. You will be in the electrical panel with the lichnikami (sound roztashovuetsya on the skin version of the booth).

It is necessary to respectfully look at the shield, to know at the new pipe that there is a special tire, walled up in the wall surface. Do not forget that the electrical panel is powered by a 220-volt voltage. On the pipe (tire) there is a small dash. Tse i є we need a deaf neutral. You will need to throw a 2.5 sq. mm ta hold yoga in the kitchen.

Important moment! Vityazhka in such situations, come to the yard through a branching machine, 6.3 A. Fasten your trunk cable over someone else's wiring and securely fix it with a nut of the same size. Like on the tire (pipe) a daily pin, it is necessary to thoroughly clean the surface, attach a metal collar and already to the new connection of the luggage wire.

Best installation exhaust ventilation at the place for cooking, I disrupt the work of the apartment ventilation system. Fahivtsi to solve such a problem with a way of probing the additional ventilation duct and bringing it to a new draft. True, this visit does not guarantee good airing of the kitchen after the installation of an accessory that will tickle us (the ceiling of the ventilation shaft is permanent, which means that the exchange of air will not be more effective). Out of a similar situation - installation of a special factory grate with a gate valve (it is sold in any budshop).

Open with a check valve to ensure a good draw

People's minds often prepare such attachments on their own. Ale better, zvichayno well, vikoristovuvati ґrati z valve (fakhіvtsі call yoga clap) factory virobnitstv. Vaughn open two. If the valve is closed on the gates, the airing of the kitchen follows the natural scheme (through the window). When the drawer is started, the position of the flap changes. Povіtrya іz primіshchennya vytyaguvatisya primusovo. The variety of descriptions of the gate guarantees the presence of the manifestation of the craving.

Air ducts for kitchens are made of polyvinylchloride (PVC) pipes or for additional aluminum corrugated pipes. Plastic constructions are built around elastic pipes or narrow boxes. They are so noiseless in robots, they are easy to mount for the small arm. The stench, moreover, mayut an indecent supply of mіtsnostі and do not psuyut kitchen interior. Corrugated pipes are installed more simply. It’s easy to bend them without using any special tools for any necessary cut. Such constructions do not vibrate, do not see the noise during the working hours of the draft. Ale їhnіy zvnіshnіy vglyad zalishaє bazhat kraschogo. To that sound mask, vikoristovuyuchi different techniques.

Connecting a drawstring - instructions for home workshops

Connecting a hood to ventilation follows one principle. With every day, the stages of such an operation can be different - everything is deposited depending on the type of unit you have brought (in the wake, suspension, and so on). Let's take a look at the process of installing a hanging attachment on the most folding butt, if the attachment is mounted hidden - at the closet.

Algorithm vykonannya robot will be like this:

1. 1. Razmіstіt shafu pіd installation ґrat z clapperboard. Check in the lower part of the opening with the necessary geometric parameters. At the upper wall of the shafi, make a square-shaped opening.
2. 2. Insert a PVC pipe or corrugation into the bottom hole. Pass yoga through the shafu. Put on the corrugations looking like a square, insert at the top opening. Coat the sticks with silicone sealant. Large gaps can be covered with mounting pins.
3. 3. Fix the box or pipe at the closet as tightly as possible, vicorist clamps, screws.
4. 4. Insert the orders and confirmations ventilation opening. You can forgive the stitching for the help of special locks (sold in the store of budmaterials) with a lapel round shape. The crushed structure is ready to work.

Rada fakhivtsiv. Lifting the hood to the fan and the ventilation shaft, try to work as little as possible by turning the corrugated box or PVC pipes. The more viginiv will be, the less will be the tightness of the aggregate. Fahіvtsі seem that one turn changes the show by 9-12%. Now you know how to build a drawstring in the kitchen as competently as possible. Watch the video of such robots and forget about the unacceptable smells, burning, increased water content and boil at the place for cooking їzhi.