The lamp is light: merekhtinnya and other problems. How to put down the measure of light-emitting lamps?

⁰

Some of the light illuminating accessories cause problems. The novelty of LED technology can make it easier to diagnose and correct these difficulties. Below is a list of malfunctions that can be blamed, with a description of the process of identifying the reasons for their appearance and possible harms. Zokrema, you know how to put down the merekhtinnya of light lamps.

Problem: merekhtinnya svetlodiodіv. Possible reason number 1: wrong voltage

LED-luminaires change the number of input parameters. Invisible voltage of the driver for the blinking of the blinking or the blinking of the light bulbs.

To fix the problem, it is necessary to change the input voltage of the driver (for example, 120 V) and the lamp (for example, 277 V). The problem may lie with their inconsistency. In this case, replace the driver, or the lamp itself in such a way that the voltage values \u200b\u200bbigalis, or, as it is impossible, install a transformer, which in an instant will secure the necessary parameters of the light lamp.

Possible reason #2: Crazy dimmer

Merekhtinnya svіtlodiodnih lamps blamed for that fall, as the lamp is not intended for a specific light controller or as the driver is not crazy with the yogo scheme that controls.

For diagnosing this problem, it is necessary to turn off the lance of the regulation of sciatica. If the light works normally, then the dimmer is otherwise unimaginable with it. Slid back to the light fixture for roses, explaining which driver is light-regulating and, as such, if it is possible to add to it.

Possible reason #3: Presence sensor or dimer

For the correct functioning of these control elements, a minimum nominal tension is required. For example, the control unit can increase the visibility of the voltage, which is at least 20 W, and the light-emitting diode is less than 10 W.

In order to install a few light-emitting lamps, it is necessary to add additional attachments to the lance, in order to increase the intensity of the tension to the one necessary for normal operation, or to replace the control unit of the presence sensor or the dimmer to the lower one, with the help of a larger assistant.

Possible reason number 4: dimming of the light regulator

The main problem of the system of regulation of the lighting of LED-lamps is the unfavorability of the light-emitting driver. Vіn razrahovanija at the maximum navantazhennya (vіmіryuєtsya at volts, amperes and watts), as if not guilty but overwhelmed.

The number of lamps, which can be installed on a single-phase dimmer, unravel, start, finish simply. For example, it is necessary to recognize, scallops of 15-watt light fixtures can be installed on a 600-watt light regulator. Partially rozpodіlu 600 to 15 indicates that 40 lamps can be controlled. Unfortunately, the result is sometimes incorrect. In fact, the attachment of such tightness allows you to light up only 6 light-emitting lamps.

If the intensity of the LED is high, the total is 15 W, and when the strum is repeated, the dimmer should be added more. In this way, a 15-watt for a light-regulating add-on will be equivalent to a 100-watt heat lamp. In this case, as if there are more than 6 lights, the dimmer will appear overwhelmed.

The average value of starting or similar splashes of a stream is equivalent to a stream, which keeps the lamp burning at an exhaustion of 100 W;

Merehtinnya light lamps can be sunk in, having done so:

go back to the technical characteristics of the luminaires for the purpose of determining the equivalent vanishing;
remove the dimmer from the line of life of the lamp and z'yasuvati, which will solve the problem;
replace the light regulator with a higher maximum voltage;
divide the lancet into sprats of navantagen.

Possible Reason #5: Insufficient Dimmer Supply

Deyakі dimeri with overly small navantazhennі function incorrectly. For their normal operation, you may need a minimum number of luminaires, outputting 25-40 W, necessary for a standard light controller. One lamp rozharyuvannya easily podpov_daє vomogam to the minimum navantazhennya. Ale LED-lamps may need four times as much.

In order to use the measure of light-emitting lamps, to eliminate the minimum dimming of the light regulator, follow:

go up to the yogo technical characteristics to determine the minimum profit;
remove the dimmer from the lance of lighting, so that you can change the edge of the problem;
replace the light regulator with a lower minimum voltage.

Problem: less light-emitting lamps. Possibly reason number 1: aiming at adjacent wiring

Merechtinnya of light lamps at the switched-on station become visible in that fall, as if the wiring was laid in parallel, along the current of the strum. The voltage is blamed on the connected conductor, as it is the cause of the flashing of the lamp.

You can solve the problem in the following ways:

in parallel with a light-emitting diode, connect a heating lamp.

Possible reason number 2: strum pіdsvіchuvannya

If vikoristovuyutsya vimikach z pіdsvіchuvannyam i svіtlodiodna lamp, merekhtinnya vіdbіvєє navitіv іn vyknennym stanі. Pіdsvіchuvannya spozhivaє strum, which charges the capacitor of the electronic circuit of the lamp equal, sufficient for sleeping.

How can I tidy up the number of light bulbs in my head? It is necessary to speed up one of the following methods:

in parallel with the lamp, connect a shunt capacitor with a capacity of 0.01-1 μF, a voltage of not less than 400 V, or a resistor with a voltage of 0.5-2 W and a support of 100 kOhm-1.5 MΩ, through which the live stream will flow;
in parallel, connect a light-emitting lamp;
replace the vimikach with the switch to the passing vimikach with the switch, connecting it so that at the switched-off station the offences of the contacts of the lamp flickered to the null wire;
replace vimikach from subsvіchuvannyam to savish;
zhivlennya pіdsvіchuvannya zdіysnyuvati through okremia zero provіd;
tidy up the vimikach's pidsvіchuvannya.

Problem: not glowing. Possibly Reason #1: Improper Conducted

In this way, it is possible to have a bad day between a light and a driver, a fence that a lamp. Change all electrical connections between LED and driver and between line and driver and change voltage. It is necessary to reconsider that all vimikachi lancers are turned on and all orders are correct.

It is necessary to check all the wires connected to the luminaire, including phase, zero, grounding, dimming lances and emergency lighting.

Possible reason number 2: poor LED

Light can be affected by transcendental vibrations, moisture and chemical or aerosol turbidity.

In this case, the lamps were damaged in a way, and the lamp was installed at the right lamp when the lamp was switched on.

Climatically, that other possession can create a vibration, as if it were built up on the light, as if it were close to the middle building. It is necessary to perekonatisya in the presence of such a splurge and either to change the vibration or to increase the distance between the neck and the body of the lamp.

Ushkodzhennya, caused by rіdinami, zabrudnennym chemical speeches or aerosols, can cause improper functioning of the light or yoga out of harmony. Your dzherela should be liquidated before they will try to fix the injustice.

Possibly reason #3: LED swearing for other reasons

As if it were otherwise, it was light, a light lamp can get out of tune in the wake of physical activity, including the fall.

In addition, the LED can be tripped as a result of voltage cuts, which can be caused when the power is turned on.

In this case, the lamps went wrong in a way and were installed in the right case with the power turned on.
The lamp should be checked for the presence of visible lights.
When the LED is connected to the driver, it is necessary to reconnect, which is switched off.

Possibly Reason #4: Driver Possibility

The light driver has several parameters. The supply of an unexpected voltage can lead to damage. Incorrect connection and filthy electrical installations also damage the building's light.

To fix the problem, check the input voltage of the driver (for example, 120 V), and then at the lamp (for example, 277). There can be inconsistency here.

It is necessary to try to install the wrong light to replace the right one, not forgetting to keep alive. If the wine is not sleeping, then the reason is in the LED lamp.

Follow all the troubles connected with the driver, including phase and zero, lances diming, thin, and fix the detected malfunctions. If it did not help, then, perhaps, the driver was damaged. From which drive it is necessary to turn to the forager.

Problem: svitlodiod live or znebarvlyuyutsya. Possible reason number 1: inconsistency between light and yoga eating

The base of the LED-lamp can be inseparable from the driver. For example, a 6-inch 10-watt light was inserted into a 6-inch 15-watt cartridge.

Larger LEDs of different intensity can be matched for the size of the same body size. Tim is not less, the light can be insane with the driver of the case, so the stinks fit one to one. It is necessary to consult with the seller or at the manufacturing plant for information on which particular LED is suitable for a particular case. Otherwise, replace the new light in case of tightness.

Possible reason number 2: the temperature of the superfluous middle is high

Maybe the mother's place is high, the temperature of the middle is too high. Heat is the enemy of light technology and the building is significantly shortening the term of the lamp's service life. Weather or climate can play an important role in squalid, arid, deserted areas and in the months due to high temperatures and humidity.

To fix the problem, it is necessary to check the temperature near the body of the lamp lower and higher than the hanging steel. If the temperature of the current situation constantly exceeds 50 ° C, the light will be fluctuating and not practical, as it was cleared up. Next, correct the problem by lowering the temperature and repeating it, or I will relocate the building. However, do not turn the light at the colossal camp. It is necessary to go back to the factory and replace the LED-lamp.

Possible reason number 3: end of term of service

For example, the service term of the light fixture can change the temperature of the light, indicator of color and light output. This is a sign that LED lamps may need to be replaced. For whom it is necessary to turn to the virobnik.

Problem: low frequency of light bulbs

Blimannya svіtla mozhe vyklikaty that eyes that reduce the practice. It is characterized by a coefficient and frequency.

The coefficient of measure of light-emitting lamps is the difference between the maximum and minimum illumination to their sum. Vіn can kolivatsya at 0% in lamps that live in the dzherel postіyny strumu, up to 100%. The value of the coefficient for heating lamps becomes 6-17%. Vіdpovіdno up to the normative vаno can be overestimated by 20%.

The frequency of light-emitting lamps should be set to the driver and up to 100 Hz for a great ballast. The optimal value of this parameter is higher than 300 Hz.

How to distort the merekhtinnya of a light-emitting lamp? You can raise a dekilcom in the following ways:

for the help of a smartphone camera when the option is turned on to extinguish the noise;
taking a picture of a cloud of light behind the smartphone's auxiliary camera - the presence of darkened swarms seems to be the presence of a pulsation;
for the help of a photodiode connected to a PC, a multimeter or headphones;
with the help of a light meter, which allows you to work like this;
guarding an object that is collapsing fast (for example, lines, olives or juli).

You can use the LED measure, which is not related to the improper operation of the lamp, in the following ways:

vikoristovuvat dzherelo fiyno fast, and not pulsating struma;
replace the luminaire with a high coefficient of measurement for an LED lamp that complies with the standards.